Topic: What happens when you are never happy with you car's power ( My Turbo Build) 56K (Read 115258 times)

boosted 00 black si · « **Reply #390 on:** March 28, 2010, 05:17:29 PM »

who did the cage?

bigdaddyvtec · « **Reply #391 on:** March 28, 2010, 06:42:44 PM »

Cage looks good MUUUUUCH better than that other pile of shit.

Pootie · « **Reply #392 on:** March 28, 2010, 07:59:14 PM »

lol , yea wayyy better. cage fits really good. tucked really close to the body of the car.

The loop behind the seats are angled slightly back to match the angle of the pannel , so you can't see the cage when you are looking at the car from the side (aside from the 2 bars that go back to the trunk).

All and all the car and cage installed cost me less than $1700 (but i got a hook up). Big thanks to Certified Racing in Garfield NJ!

danz · « **Reply #393 on:** March 28, 2010, 08:05:51 PM »

can you take some pics of how the main hoop braces are welded to the floor?

i was reading the 2010 handbook the other day and it stated on FWD Unibody cars the two support bars needed to be welded to a 1 5/8ths bar that goes from one rocker sill to the other.

Joseph Davis · « **Reply #394 on:** March 28, 2010, 08:36:59 PM »

Some local guys bought a gutted dash Dodge Colt with the whole caged/slicks/4G63/no dash or heater core treatment. They ran some dinky tiny heater core out of a scrap pile and a 12V computer case fan with cardboard venting just dumping in the floorboard and it heated the car great. If the cage cockblocks your ducting/climate control stuff don't worry, you can do something and tuck it up out of the way.

Pootie · « **Reply #395 on:** March 28, 2010, 09:32:00 PM »

Quote from: danz on March 28, 2010, 08:05:51 PM

can you take some pics of how the main hoop braces are welded to the floor?

i was reading the 2010 handbook the other day and it stated on FWD Unibody cars the two support bars needed to be welded to a 1 5/8ths bar that goes from one rocker sill to the other.

yea , i will have to add a bar. As seen here in this pic

butt instead of cutting the existing bar. This is the option for most people with cages pre 2010,

Joseph Davis · « **Reply #396 on:** March 28, 2010, 09:50:00 PM »

I'd triangulate the rear bars, as well.

crxvtec91 · « **Reply #397 on:** March 28, 2010, 11:22:15 PM »

Quote from: Pootie on March 28, 2010, 07:59:14 PM

Big thanks to Certified Racing in Garfield NJ!

Fuck those cheap flaming cum drinking cheap fags!

Pootie · « **Reply #398 on:** March 29, 2010, 07:58:23 AM »

Quote from: crxvtec91 on March 28, 2010, 11:22:15 PM

Quote from: Pootie on March 28, 2010, 07:59:14 PM
Big thanks to Certified Racing in Garfield NJ!

Fuck those cheap flaming cum drinking cheap fags!

lmaoooo
i can't win on this site..

is there ANYONE you guys don't hate?
ho man, el oh el!

danz · « **Reply #399 on:** March 29, 2010, 02:58:51 PM »

fuck i was hoping i wouldnt have to mess around with the lower brace. what a pain in the ass.

i almost just want to get a 6 point and say fuck it, and call it a day if i hit 135mph or 10.0

crxvtec91 · « **Reply #400 on:** March 30, 2010, 09:06:27 AM »

Quote from: Pootie on March 29, 2010, 07:58:23 AM

Quote from: crxvtec91 on March 28, 2010, 11:22:15 PM
Quote from: Pootie on March 28, 2010, 07:59:14 PM
Big thanks to Certified Racing in Garfield NJ!

Fuck those cheap flaming cum drinking cheap fags!
lmaoooo
i can't win on this site..

is there ANYONE you guys don't hate?
ho man, el oh el!

i used to work for Japanese engines out of paterson, nj. Been to almost every well know shop in the tri state. There are really, really few shops that i would trust.

Hey when someone comes to bring you a motor or trans dont make them wait around for hours trying to dick them around, only to piss him off. Then when the person gets in your face all of a suden they come up with the money in a hart beat.

I hate most shops in the tri state/ shop owners/ wanbe tunners.

Pootie · « **Reply #401 on:** March 30, 2010, 05:57:19 PM »

Quote from: crxvtec91 on March 30, 2010, 09:06:27 AM

Quote from: Pootie on March 29, 2010, 07:58:23 AM
Quote from: crxvtec91 on March 28, 2010, 11:22:15 PM
Quote from: Pootie on March 28, 2010, 07:59:14 PM
Big thanks to Certified Racing in Garfield NJ!

Fuck those cheap flaming cum drinking cheap fags!
lmaoooo
i can't win on this site..

is there ANYONE you guys don't hate?
ho man, el oh el!

i used to work for Japanese engines out of paterson, nj. Been to almost every well know shop in the tri state. There are really, really few shops that i would trust.

Hey when someone comes to bring you a motor or trans dont make them wait around for hours trying to dick them around, only to piss him off. Then when the person gets in your face all of a suden they come up with the money in a hart beat.

I hate most shops in the tri state/ shop owners/ wanbe tunners.

trust me , i hear ya!

different interactions with shops have different results.

I did however had to drop the car off on a Wed and they mixed up my appointment with some other dude. So i ended up droping it off the following Sat, and picked it up on my next day off which was a week later ( the next Sat).

Which was one hell of a turnaround time. I had a few other shops say it was a 2 week wait just to get the car in and 2 weeks for the job to complete.

Pootie · « **Reply #402 on:** April 03, 2010, 12:10:20 AM »

got the dash notched and installed today.. No heatttttt

All done...

Tomorrow is to clean up the inside, and paint it black. Also paint the hood and front bumper Grey to sorta match the rest of the car.

Towdogg · « **Reply #403 on:** April 03, 2010, 02:00:08 AM »

Being from new england I would say your gonna want keep that heat....

Pootie · « **Reply #404 on:** April 05, 2010, 12:41:27 PM »

Quote from: Towdogg on April 03, 2010, 02:00:08 AM

Being from new england I would say your gonna want keep that heat....

ehh, i wanted to. But once i started cutting the dash. I had to cut the ducts. So i just said fuck it.!!

This won't be a "street car". More than likely will not be driven on the street for a long enough period to need heat.

Lot of layers FTW!!

crxvtec91 · « **Reply #405 on:** April 05, 2010, 06:20:47 PM »

Quote from: Pootie on April 05, 2010, 12:41:27 PM

Quote from: Towdogg on April 03, 2010, 02:00:08 AM
Being from new england I would say your gonna want keep that heat....

ehh, i wanted to. But once i started cutting the dash. I had to cut the ducts. So i just said fuck it.!!

This won't be a "street car". More than likely will not be driven on the street for a long enough period to need heat.

Lot of layers FTW!!

Dr.D (Joe) had a lil heater that was powered by the sig outlet. And he DD in the winter.

Pootie · « **Reply #406 on:** April 06, 2010, 11:43:15 AM »

Quote from: crxvtec91 on April 05, 2010, 06:20:47 PM

Quote from: Pootie on April 05, 2010, 12:41:27 PM
Quote from: Towdogg on April 03, 2010, 02:00:08 AM
Being from new england I would say your gonna want keep that heat....

ehh, i wanted to. But once i started cutting the dash. I had to cut the ducts. So i just said fuck it.!!

This won't be a "street car". More than likely will not be driven on the street for a long enough period to need heat.

Lot of layers FTW!!

Dr.D (Joe) had a lil heater that was powered by the sig outlet. And he DD in the winter.

yea, i might look into that. I won't be driving it tho.

But a slight update. Got my mounts in.. "The Vibrator"

crxvtec91 · « **Reply #407 on:** April 06, 2010, 12:41:34 PM »

Damn talk about solid mounts

bigdaddyvtec · « **Reply #408 on:** April 06, 2010, 12:44:04 PM »

Quote from: crxvtec91 on April 06, 2010, 12:41:34 PM

Damn talk about swinging on nuts

LOL

Cooljnateman · « **Reply #409 on:** April 06, 2010, 01:10:23 PM »

can you say mobile vibrator...them mounts is almost as stiff as my dick

Pootie · « **Reply #410 on:** April 06, 2010, 01:26:58 PM »

Quote from: Cooljnateman on April 06, 2010, 01:10:23 PM

can you say mobile vibrator...them mounts is almost as stiff as my dick

lol, yea i was trying to avoid them. But i was getting things like this every 3-4 months (or every 10 or so passes on slicks)

I felt like i had to switch to Soilid to keep the motor still, and lessen the chance of broken axels ( since i'm still on my old DSS 3.9s).

glustic · « **Reply #411 on:** April 06, 2010, 02:32:46 PM »

Sweet baby jesus that is going to be one hell of a vibrator. Keep on the updates, cage looks good

d-rail · « **Reply #412 on:** April 08, 2010, 04:47:41 AM »

The best and cheapest way to do it is having a good friend with a machine shop and skills and have them make you a steel mount using your old mounts as a blueprint.

widebody93 · « **Reply #413 on:** April 08, 2010, 05:04:13 AM »

Yep thats how we done it....Jimmy hooked me up with my inserts, but not a baller at the lead weight you had on your D... That fucker weighed like 40 pounds...

d-rail · « **Reply #414 on:** April 08, 2010, 05:21:11 AM »

The way I said does weigh a bit more than those solid aluminum mounts but your aluminum mounts will start giving and warping. Its just the nature of aluminum.

bigdaddyvtec · « **Reply #415 on:** April 08, 2010, 05:26:54 AM »

Actually... no. They won't.

d-rail · « **Reply #416 on:** April 08, 2010, 05:43:23 AM »

Quote from: bigdaddyvtec on April 08, 2010, 05:26:54 AM

Actually... no. They won't.

Not to argue spike but Rob at TPR showed me some of his aluminum mounts that his hatch turned into chewing gum. Pretty rough shit

bigdaddyvtec · « **Reply #417 on:** April 08, 2010, 05:53:17 AM »

Quote from: bigdaddyvtec on April 08, 2010, 05:26:54 AM

Actually... no. They won't.

crxvtec91 · « **Reply #418 on:** April 08, 2010, 12:25:48 PM »

When is the motor going in?

widebody93 · « **Reply #419 on:** April 08, 2010, 03:46:07 PM »

Quote from: d-rail on April 08, 2010, 05:43:23 AM

Quote from: bigdaddyvtec on April 08, 2010, 05:26:54 AM
Actually... no. They won't.

Not to argue spike but Rob at TPR showed me some of his aluminum mounts that his hatch turned into chewing gum. Pretty rough shit

I seen them too, but I dont think they were the highest of quality in aluminum. looked like coke can shit... But my inserts are 4030 steel or tool steel...hmm carnt remember but they work just fine after we cut,rewelded, to position motor for better axle alignment for the twisties. No more binding on drivers side anymore or popped axle boots

News:

Author Topic: What happens when you are never happy with you car's power ( My Turbo Build) 56K (Read 115258 times)