:::RHMT::: Real Home Made Turbo
General Category => Forced Induction => Topic started by: HiProfile on March 12, 2010, 01:40:09 AM
-
Should I buy this thing? It's around 2 bones shipped.
Supposedly this turbo has very little shaftplay, spins freely, other pics show just soot not oil. Looks like it sat outside compressor-up for a year. I'd probably just douche it out and only need it for a few hundred miles. There is another one for a bit cheaper, but it's the 8-blade version - and it's much cleaner. I'd almost want that for a cunt-hair better spool.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fimg54.imageshack.us%2Fimg54%2F2479%2Fdsc00hx35.jpg&hash=da8aee45848de43ad5530d47575a3414d1cb2e2d)
Basicly I want to know how much abuse/neglect a Hoeslut can take before it's really just scrap.
-
They can take a lot. That one is probably off a marine engine. That said buy the 8 blade since it's better and cheaper.
-
a bone is 1 dollar
-
...That said buy the 8 blade since it's better and cheaper.
I disagree, about the 8 blade being better. However if it is cleaner and cheaper, then buy it, it is not a significant difference.
-
fair bit of oxidisation and corrosion there........ therefore.........
id say that thing slid out of julio's ass in the last shart thread.....
:mexi:
-
fair bit of oxidisation and corrosion there........ therefore.........
id say that thing slid out of julio's ass in the last shart thread.....
:mexi:
Thanks, dude. I was just taking - trying to take - a bite of guacamole when I read that jewel bead.
-
I'm not too concerned about overall flow, 50+ lb/min is much more than I'll need. However the 8-blade's larger exducer (83mm vs 76mm) would help in spoolup, as would just the extra blade itself.
I'm also planning on grinding the divider down and putting a flapper in there, to make it an integrated quick spool valve. 6cm for spoolup, 12cm for topend. Depending on how that goes, I may drop $125 or $175 for a 18cm or 16cm housing. It would spool like an hy35 but would pull like crazy to redline.
http://www.gillettdiesel.com/18cm2non-wastegatedturbinehousing-1-1.aspx (http://www.gillettdiesel.com/18cm2non-wastegatedturbinehousing-1-1.aspx)
-
That one looks pretty haggered. Mine was about the same when I bought it. (if i find the thread or pics ill post them)
I thought it will be good, not too much shat play and cleaned up pretty easy..... but a buddy said he'll take it to work and check it out. Long story short it needed a full rebuild.
-
I'm not too concerned about overall flow, 50+ lb/min is much more than I'll need. However the 8-blade's larger exducer (83mm vs 76mm) would help in spoolup, as would just the extra blade itself.
I'm also planning on grinding the divider down and putting a flapper in there, to make it an integrated quick spool valve. 6cm for spoolup, 12cm for topend. Depending on how that goes, I may drop $125 or $175 for a 18cm or 16cm housing. It would spool like an hy35 but would pull like crazy to redline.
http://www.gillettdiesel.com/18cm2non-wastegatedturbinehousing-1-1.aspx (http://www.gillettdiesel.com/18cm2non-wastegatedturbinehousing-1-1.aspx)
I've got an 18cm on my built ls/vtec its not too bad.
-
That thing should clean up just fine. I saw a guy with one much dirtier that cleaned up perfectly. I wish I could find it, it was just recently too.