:::RHMT::: Real Home Made Turbo
General Category => Hybrid/Tech => Topic started by: lilpooh21186 on March 11, 2009, 02:19:42 AM
-
THis is my first write up so i figured i would start some where simple
Jack up the car take tires off then remove lower ball joint (easiest with a ball joint fork)
and pick up whole knuckle assyembly and move it to the side.
i then drain tranny fluid and pop axles out of tranny with a prybar. i used random shit to stop the knuckles from moving back in place.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F065.jpg&hash=8f4db28ea5b34fad914574bdd157335613ca8d33)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F068.jpg&hash=05e59ea1bd0b12173d425804a069ca26e0934635)
Remove intake tube and starter 2 bolts for the starter Must be removed or tranny Wont come off.
Also a good idea to unplug harness from the head for the coolent temp and all that other B/S Unplug battery and all ground from tranny to Chassis remove lower tranny mount 3 bolts.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F071-1.jpg&hash=0825195782348d07dbb2272114160eaa0aa85ce5)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F067.jpg&hash=8116eecf9063c39b241bb08fc3677272ddda18e6)
Now after that near where the starter was remove 1 bolt from the Rear T bracket while.
Then get under the car and remove the 2 bolts that secure the tranny to the T bracket
1 bolt for the shifter stabilizer.
If you dont want to fuck with the bitch pin then remove 2 12mm from the Shifter linkage it self.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F072-2.jpg&hash=c4addef720b9b74177b27d8229bde5f787cd33a6)
( Motor should be swing like my nuts W/ stock motor mounts).
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F076.jpg&hash=6116facdbdad617002ad25c37a9140b366a421fa)
Then remove 7 Bolts from the transmission 2 on top 2 front side 1 rear and 2 for the dust shield
And 1 bolt from the passenger main motor mount.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F075-1.jpg&hash=9a332825ea53dc125dff1d17a9fa986574b71180)
7 BOLT PICS WILL BE UPDATED.You should now see the seal from the block to tranny open a little bit.
Secure the tranny with a Jack lower it and the trans should basicly fall off now ( may take some rocking)
drag that bitch out the way and jack the motor back up secure it with a jack stand.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F079.jpg&hash=249423461283977b83ee32475c5ab83a0c83b09f)
to remove Clutch there are 6 10mm 12pt bolts the are kindoff a bitch to remove
if you dont have air tools what i did was start from the bottom
tap a Wrench with a hammer till they came loose.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi188.photobucket.com%2Falbums%2Fz204%2Flilpooh21186%2F077.jpg&hash=b7ff59048e95f86f07fc1948ea011f07a5824042)
i didnt use the alignment tool eyballing it is a bitch
basicly dont over tighten the 12pt bolts they will snap.
You can choose to get the flywheel surfaced i didnt b/c this motor will be coming out in a few months.
Put the tranny back on the jack lift it up get the tranny to sit flush with the motor tighten the 7 bolts
then the main pass motor mount lower mount snap axels in to place reinstall knuckles and all that other
shit take it easy for a Few hunderd best way to Refill tranny i found is to take a funnel and a hoze
remove the speed sensor. and fill from that Hole.
-
Wow i fucked this up stay tuned for my Det Cans