:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Official RHMT TANK! that's right i said a TANK! (link)

Pages: [1]   Go Down

Author Topic: 10 minute tool fab  (Read 6312 times)

7808

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2513
10 minute tool fab
« on: July 18, 2010, 11:10:33 PM »

im sure someone on here has made one of these before, but just in case heres a thing i made out of shit layin around



took a cheap 4" c clamp and tried to wire wheel as much of the already half burned up from welding coating off the one side and hit the little pivot deal too, cut 2 pieces off some angle i had and welded .  works good for tacking pipes together instead of tape or magnets sometimes
Logged

t_cel_t

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3147
Re: 10 minute tool fab
« Reply #1 on: July 18, 2010, 11:13:23 PM »

sweet
Logged
malone labe

I think all cop cars need to have turbo. nbspnbsp Then they would understand the necessity of putting your foot down and how uncontrollable the urge is to fucking rail on that shit.

onlyflash944

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2741
  • Jack of all trades, Master of none
Re: 10 minute tool fab
« Reply #2 on: July 18, 2010, 11:28:26 PM »

arc welding gloves and my left hand works well too
Logged

You read some forums? nbspnbsp Cool, I tune cars.

  Its your fucking car, if you want to hack it up fucking go for it.

PhilStubbs

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 5885
  • Teh Secksy.....I has it
Re: 10 minute tool fab
« Reply #3 on: July 19, 2010, 07:09:35 AM »

I have been thinking about doing the same thing but with one of those vicegrip style welding clamps.
Logged
obd1>gtgtall

 fucking box started smoking and i saw a flame start up so i grabbed a bucket of water and splashed it on the breaker box.

BoostedSchemes

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 18561
  • ☂BloodRaincoat☂
Re: 10 minute tool fab
« Reply #4 on: July 19, 2010, 11:44:33 AM »

then when youre done welding you take that bad boy outside and put it to lil streetblockas cranium a few times to expand it for 3" pipe
Logged
All posts before 8am and after 3pm are produced under the influence of alcohol.


Major Loser, please tell me how to be smart and interesting like you~

jay

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 906
Re: 10 minute tool fab
« Reply #5 on: July 20, 2010, 02:54:39 AM »

 fuck yes...

this is why i love rhmt
Logged

I want you to die

 
Stone cold killin sandnog from the motherfuckin low cash, fuck ya, getcha pee pee wet. ♥#9829#9829 ♥#9829#9829 ♥#9829#9829   http://img713.imageshack.us/img713/3871/detroit187.jpg

SgtB

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 406
Re: 10 minute tool fab
« Reply #6 on: July 20, 2010, 08:56:48 PM »

Sweet. I was going to buy the Hobart pliers. I'm going murder a C-clamp.
« Last Edit: July 20, 2010, 09:59:20 PM by SgtB »
Logged

snm95ls

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3662
Re: 10 minute tool fab
« Reply #7 on: July 20, 2010, 09:08:07 PM »

Simple and it works.

Nicely done.

DasPoop

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1761
Re: 10 minute tool fab
« Reply #8 on: July 27, 2010, 09:45:42 PM »

piece of long angle iron in a vice works pretty well to
Logged
Na mike:"quotquotthe one i had was a real bbw, not just a fat chick, but a huge fat chick"quotquot

PhilStubbs

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 5885
  • Teh Secksy.....I has it
Re: 10 minute tool fab
« Reply #9 on: July 27, 2010, 09:58:05 PM »

Not under a car
Logged
obd1>gtgtall

 fucking box started smoking and i saw a flame start up so i grabbed a bucket of water and splashed it on the breaker box.

N1 Andy

  • Full Member
  • ***
  • Offline Offline
  • Posts: 131
Re: 10 minute tool fab
« Reply #10 on: July 30, 2010, 04:38:33 PM »

unless youre tigging shit, i dont see the need
Logged
401/298 LeeD Tuned Stock Bottom End LS/Vtec
GFIgarage
Pages: [1]   Go Up