:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Daspoop/Trevor YOU WILL BE MISSED, RIP (link)  :'(

Pages: [1]   Go Down

Author Topic: need a fitting m8x1.25-m10x1.25  (Read 3082 times)

t_cel_t

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3147
need a fitting m8x1.25-m10x1.25
« on: August 24, 2010, 07:50:42 PM »
anyone know where i can find a female m8x1.25 to a male m10x1.25

i need to go from a stevemode line (male m8x1.25) to a subaru turbo (female m10x1.25)




and some metric bitches







Logged
malone labe

I think all cop cars need to have turbo. nbspnbsp Then they would understand the necessity of putting your foot down and how uncontrollable the urge is to fucking rail on that shit.

BoostedSchemes

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 18561
  • ☂BloodRaincoat☂
Re: need a fitting m8x1.25-m10x1.25
« Reply #1 on: August 24, 2010, 08:12:31 PM »
ok, go buy one??
mcmaster carr
Logged
All posts before 8am and after 3pm are produced under the influence of alcohol.


Major Loser, please tell me how to be smart and interesting like you~

ratcityrex

  • I Get Blown Daily
  • Global Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 7374
Re: need a fitting m8x1.25-m10x1.25
« Reply #2 on: August 24, 2010, 08:14:13 PM »
Speedway motors maybe?
Logged
New setup is old bottom end with a hype r head with gsr cams. built lsv with hx35 @ 26psi on pump gas
LEED tuned! 434hp/329tq http://www.youtube.com/watch?v=_pbDXZxZdZs
http://www.realhomemadeturbo.com/forum/index.php/topic,16195.0.html

Old Setup B18a1 296hp/289tq LEED Tuned 20psi on pump! http://www.youtube.com/watch?v=2Yj-Z90j4W4   
http://www.realhomemadeturbo.com/forum/index.php/topic,205.msg2437.html#msg2437

DasPoop

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1761
Re: need a fitting m8x1.25-m10x1.25
« Reply #3 on: August 24, 2010, 08:23:48 PM »
call up mark at one6 motorsports i had to use one on my old ihi build

(847) 593-9490
Logged
Na mike:"quotquotthe one i had was a real bbw, not just a fat chick, but a huge fat chick"quotquot

t_cel_t

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3147
Re: need a fitting m8x1.25-m10x1.25
« Reply #4 on: August 24, 2010, 10:17:26 PM »
Quote from: DasPoop on August 24, 2010, 08:23:48 PM
call up mark at one6 motorsports i had to use one on my old ihi build

(847) 593-9490
will try tomorrow

Quote from: BoostedSchemes on August 24, 2010, 08:12:31 PM
ok, go buy one??
mcmaster carr
they dont have them



fuck it i might resort to drilling out a bolt and welding the smaller nut on top. anyone know how to kill the heat treating on a grade 5 bolt? or will i be able to drill through it just fine.
Logged
malone labe

I think all cop cars need to have turbo. nbspnbsp Then they would understand the necessity of putting your foot down and how uncontrollable the urge is to fucking rail on that shit.

sloTeg

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 30
Re: need a fitting m8x1.25-m10x1.25
« Reply #5 on: August 24, 2010, 10:54:44 PM »
http://www.slowboyracing.com/

this guys hooked me up a few years ago with the same thing, stealthmode oil line to a subaru tdo4-L turbo. wont be able to find it on the site, but give them a call and they should be able to get what you need.
Logged

jabberwock

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 1135
Re: need a fitting m8x1.25-m10x1.25
« Reply #6 on: August 24, 2010, 10:56:59 PM »
Drill and tap a m10 bolt...
Logged
Pages: [1]   Go Up
« previous next »