:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

RHMT DIY Hub Dyno?!?!? check it. (link)

Pages: [1]   Go Down

Author Topic: where to get banjo fittings that attach to mcmaster lines  (Read 10906 times)

7808

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2513
where to get banjo fittings that attach to mcmaster lines
« on: March 18, 2009, 10:37:15 AM »

anyone know where to get cheap banjo fittings that could be used with mcmaster braided lines with the 1/8 ends? i think the size i need is for 10mm banjo

somthin like this, but im not sure what AN sizes
are what and those are like $16

Brake Banjo Fitting
-04 AN - 10mm Banjo Fitting
361-997641
Logged

ratcityrex

  • I Get Blown Daily
  • Global Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 7369
Re: where to get banjo fittings that attach to mcmaster lines
« Reply #1 on: March 18, 2009, 11:20:06 AM »

10mm to -4an or -3an
Price: $22.99 PR

Speedwaymotor
http://www.speedwaymotors.com/BANJO-FITTING-3and8-or-10MM-to-AN,6468.html




Just go type in banjo in there search function. I have had great luck with there braided  lines. The best price around.
Logged
New setup is old bottom end with a hype r head with gsr cams. built lsv with hx35 @ 26psi on pump gas
LEED tuned! 434hp/329tq http://www.youtube.com/watch?v=_pbDXZxZdZs
http://www.realhomemadeturbo.com/forum/index.php/topic,16195.0.html

Old Setup B18a1 296hp/289tq LEED Tuned 20psi on pump! http://www.youtube.com/watch?v=2Yj-Z90j4W4   
http://www.realhomemadeturbo.com/forum/index.php/topic,205.msg2437.html#msg2437

7808

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2513
Re: where to get banjo fittings that attach to mcmaster lines
« Reply #2 on: March 18, 2009, 02:18:25 PM »

that... is what i posted above, but yours cost more ..  so is -4 an  the same thread as 1/8 npt ?
Logged

ratcityrex

  • I Get Blown Daily
  • Global Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 7369
Re: where to get banjo fittings that attach to mcmaster lines
« Reply #3 on: March 18, 2009, 02:51:17 PM »

but yours cost more .. 

$22.99 PR
= 2 of them of them
Or $11.495 Each  ;)
Logged
New setup is old bottom end with a hype r head with gsr cams. built lsv with hx35 @ 26psi on pump gas
LEED tuned! 434hp/329tq http://www.youtube.com/watch?v=_pbDXZxZdZs
http://www.realhomemadeturbo.com/forum/index.php/topic,16195.0.html

Old Setup B18a1 296hp/289tq LEED Tuned 20psi on pump! http://www.youtube.com/watch?v=2Yj-Z90j4W4   
http://www.realhomemadeturbo.com/forum/index.php/topic,205.msg2437.html#msg2437

Tim

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2632
Re: where to get banjo fittings that attach to mcmaster lines
« Reply #4 on: March 18, 2009, 08:51:38 PM »

that... is what i posted above, but yours cost more ..  so is -4 an  the same thread as 1/8 npt ?

npt is thread seal an(-an) is standardized thread ranging, with a tapered seal at the end (comrpession fitting)

To clarify this a little more for someone that might not understand:

NPT is National Pipe Thread and is a tapered thread.  The outside diameter at the end of the thread is smaller than the outside diameter at the base of the thread, so it looks like a threaded cone.   The female mate is opposite ie the hole gets smaller the deeper it goes.  These types of seals it is good to use teflon tape or pipe dope.

AN has SAE or straight threads, like bolt outside diameter of the threads stay the same size from beginning to end.  The taper at the end of the fitting meets a matching taper inside the female part so seal, the threads have absolutely no effect on sealing aside from profiding holding force.  These fittings DO NOT need teflon tape or any kind of pipe dope (even though I see it every time I walk into a customer's plant  :P)

the number -4, -8 etc. is common sizing and it is the size in the number of sixteenths.  -4 = 4/16 or 1/4"  -8 = 8/16 or 1/2" etc.  This usually refers to the inside diameter of the hole, or id.  Except tubing then it refers to the outside diameter or OD.

I like those pictures though, good visual reference for pulling fittings out of a bin.
Logged

glustic

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2502
  • Jay is a fucking homo
Re: where to get banjo fittings that attach to mcmaster lines
« Reply #5 on: March 18, 2009, 09:09:58 PM »

http://www.anplumbing.com/shop/index.php?shop=&dept=Banjos

Banjo Adapter -4 male to 10mm Hole diameter .425 height   $ 7.41

I am the winnar
Logged
fucking box started smoking and i saw a flame start up so i grabbed a bucket of water and splashed it on the breaker box.. nbspnbsp BIG FUCKING MISTAKE

-BUK
Pages: [1]   Go Up