:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Official RHMT TANK! that's right i said a TANK! (link)

Pages: [1] 2   Go Down

Author Topic: scottdh20's project turbo d15b7  (Read 12494 times)

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
scottdh20's project turbo d15b7
« on: November 09, 2009, 09:41:44 AM »

so i will start off by saying that im sorry if some of this doent make sence im going to be cut and pasteing it from another forum to save me some time.

 it's now boosted



well i have almost all my parts for a turbo build so i figured i'd start a build thread. i have a new computer so i dont have to many older pics but i'll try to start at the begining.

in nov. 07 i bought a cx hatchie with a wonderful d15b8 in it, soon after purchase i started noticing the temp going up and some funny idol problems. i had a spare b7 head lying around so i figured i do a head swap and get 30 extra ponies. well turns out there are three snapped head bolts, to top it off the easy out snapped off in the block doing the last hole. thats when that block got stripped down for spare parts and went to the trash can.



so i took my perfectly good 4dr and ripped its heart out





^^^^^my buddy matt has helped me out alot w/ this project.

then put it in the hatch



some goodies for the new motor



also at autozone i noticed that the code for d16z6 and d15b7 valves were the same. so in place of the old worn out ones in the d15 got a skunk2 upgrade(exhaust side fit intake didnt, so all new oem's went on the intake side or it may have been the other way around not sure)




current mod list:
engine:
rebuilt d15b7
skunk2 exhaust valves
new oem intake valves
a6 valve springs
a6 cam
red aem true time cam gear
arp head studs
y8 head gasket
napa refinished head (milled true, valve guids, valve seals, cleanned it up real good including combustion chambers)
custom 2.25 exhaust w/ no cat and a fart can
z6 intake manifold
spoon oil cap
full tune-up about 5k ago(timing belt,water pump, oil pump, starter, alternator, bunch of sensors, just overhauled it)
garrett gt-17 turbo
hf mani w/ adapter plate
2.5in down pipe
2.5 cold side, 2in hot side ic pipes
blitz blow off valve
godspeed fmic
rc 310 cc injectors
stealthmode oil line kit
tuner toys block fitting
ngk- bkr7e @.027


drivetrain:
egay short shifter
f1 stage 3 sprung 6 puck clutch and performance pressure plate
dx 5-speed (been searchin the junkyards for a ex/si)

rollers;
16" eagle alloys series 193 (i painted them gunmetal)
toyo fz4's

exterior:
si-r front lip
amber corners
50/50 tail lights
spoon style mirrors
carbon fiber duckbill
custom evo style hood ( yeah i made that, not bad for a days work)
rain gaurd things on the windows
egay coil over sleeves on stock shocks....yeah yeah yeah i know
diy black housing headlights

interior:
corbeau stationary bucket on driver side
no name pass racing seat
4 point harnesses
clock
jdm center audio consol
autometer dash gauge pod
5" autometer monster tach
2 5/8s water temp gauge
carbon fiber block off plate w/ autometer boost and oil pressure gauges
carbon fiber gauge cluster
rear strut bar
red l.e.d's in gauge cluster(looks nice)
titanium looking shift knob
armrest
v3 dvd/cd player
pioneer speakers and 12"sub

plans for next season:

either
jdm d15b crank with fj dist. custom length i-beams and vitaras
or
h-beams from hungry.....lol with vitaras
t3/t4 .50 or 57 trim
spa topmount mani
new 3" dp and exhaust
550-650 inj.
new tune

si tranny with lsd installed or jdm d15b tranny w/ oem lsd

300-350whp out of a d15b7.......dont ask me why i just wanna do it









this is from this morning




as soon as it warms up i gonna respray the whole car white cuz it looks like ish right now as well as a new pass fender
next spring or maybe later this year i was thinking i may go with a fiji blue pearl with bronze rims, bronze engine bay and interier








here a few more pics






best over flow bottle ever....well second best swapping to a rockstar suger free here soon




now here is the turbo goodies

hf maniw/ adapter plate and garrett gt-17 turbo



front mount intercooler



blitz bov and custom black mandrel bent piping(turbo to ic is 2" and ic to tb is 2.5")




stock gt-17 down pipe and a bunch of random ic pipes and couplers off stock volvos, sabbs and what ever else i saw boosted at the junk yard



shaving my valve cover



well thats about it for right now.....i'll update soon

this sucks ass....now i gotta track down a new wastegate or buy one off ebay for $60





« Last Edit: November 09, 2009, 01:24:46 PM by crxvtec91 »
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #1 on: November 09, 2009, 09:46:10 AM »

ek side skirts


installed




heres the bumper, sanded it, then sprayed a little white i had lying around on the spots where the paint had flacked a bit. i forgot to get a pic of the finished product i'll do that tonight
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #2 on: November 09, 2009, 09:46:57 AM »

i need a paint job bad, its next on the list after the turbo

but heres a few pics



Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #3 on: November 09, 2009, 09:47:43 AM »

pics of new parts as promised.....

xenocrone base map and chipping kit


autometer sport comp boost gauge


autometer sport comp oil pressure gauge


boost controler




just need to measure the turbo oil feed and drain connections on the turbo so i can order a kit from greg and it'll be ready for install
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #4 on: November 09, 2009, 09:48:29 AM »

was going to go with a go-autoworks oil line kit but ended up getting a used one on another forum dirt cheap





just hooking all the lines up for the boost and oil press gauges:




Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #5 on: November 09, 2009, 09:49:03 AM »

parts pile set up for install:





now lets have some fun, temps in the mid 50's and sunny as hell:




Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #6 on: November 09, 2009, 09:49:49 AM »

buddy that came over decided to show me what a "real" turbo looks like.....lol he's looking for 9's this year in a maxima




more fun in the sun



Logged

Lowerit

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 101185
Re: scottdh20's project turbo d15b7
« Reply #7 on: November 09, 2009, 09:49:58 AM »

Rota RB's FTW

Get bigger injectors.

Logged
fuck you

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #8 on: November 09, 2009, 09:50:32 AM »

img]http://i114.photobucket.com/albums/n273/scottdh20/186.jpg[/img]

tuner toys block fitting







im a genius, i had to turn my turbo around cuz it wouldnt fit......then it still wouldnt fit...damn it......oh ::lightbulb:: i notched out the mount, fits like a glove


Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #9 on: November 09, 2009, 09:51:55 AM »

yawn....oh good morning





time to try to fit the bumper....uh oh doesnt fit, good thing i bought a cut off wheel




Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #10 on: November 09, 2009, 09:52:50 AM »




i see you:



rc 310's




blitz bov oh how sexy you sound

Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #11 on: November 09, 2009, 09:53:23 AM »




gotta represent the no-tec lovin'



gauges





Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #12 on: November 09, 2009, 09:54:10 AM »



uh oh more problems......damn bleeder valve



$50 bucks later thats fixed


im a ricer...stickers ftw!





ok one sec i'll be right back gotta go for a test drive........holy sh*t ....i love it

some final adjustments and were good to go!





thanks for looking......more to come soon
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #13 on: November 09, 2009, 09:54:51 AM »

sorry it took so long, i kept forgetting to bring my camera to work.....but here they are!!

my old rims w/ new front tires + pimpin white paint job







Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #14 on: November 09, 2009, 09:55:44 AM »

gauges

Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #15 on: November 09, 2009, 09:56:12 AM »

started a little mild tuck job. i haven't done the other side yet, but it looks better

before




during





Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #16 on: November 09, 2009, 09:57:00 AM »

thank you, non-vtec FTW, i mean vtec is amazing in N/A apps but if its turbo'd notec is the way to go.

small update, cleand up the bay a little w/ some engine brite degreaser and re spayed my back-up valve cover while i wait for my other one i shaved to get back from being sand blasted.






Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #17 on: November 09, 2009, 09:57:46 AM »

so i hit my goal of mid 14's, but was dissaponted because my traps revieled i had quite a bit more, easy mid to low 13's with slicks and si tranny . so next time hopefully will be with slicks




camera died right befor the 14.5 pass but here is the 14.6

Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #18 on: November 09, 2009, 09:58:34 AM »

only video i got....worst run of the night at like 15 flat, launched at 2k....lol i stagged late and the tree began to fall as i was getting ready, started to get on the trotal at 2nd yellow and just let it go on third so horrible launch....then my camera died but i did get some good runs in




here was the best run, i know i need to get my 60ft down but launch control is set a 4k and is going to be getting raised to 6k before i head out to the track again



and my new shoes




should be able to get a mid to high 13 next trip with my launch control fixed
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #19 on: November 09, 2009, 09:59:20 AM »



went to the track, well it sucked to say the least... it was like 45* out and it was misting out here and there. they said they preped the track in the morning and then they didnt go over it again the whole day...they said its to late in the season to be going over the track ever couple hours.....the first 60ft were ok but at about the 60ft mark the track got slick.....

i'll have some vids up later today or tomorrow....

either way i got like a 14.3 @ 96-98mph somewhere in there but with a 1.92 60ft...........because 1st gear it would rip, shift to second and as the rpms start climbing the tires just break loose? but i guess alot of people had the same problem with the track being prepped very well until the 60ft marker, then it just got slick as hell.

i guess it was ok cuz i forgot a helmet and if i ran 13.999 or faster they would have kicked me out......i hope that there will be a decent day before the season ends
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #20 on: November 09, 2009, 09:59:59 AM »

need to get my ebrake fixed this was one of my best burnouts, and its pretty pathedic...lol .... i found out later the chick kept waveing me forward out of the waterbox......without an ebrake i need the waterbox....lol



the almost nothing burnout







heres one of the slips
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #21 on: November 09, 2009, 10:00:58 AM »

look what i just got.....




autopower 4pt bolt in cage. still needs to be installed, i just put it in to test fitment, got it used on a local forum dirt cheap. im going to have a harness bar welded in sometime this winter or early spring
Logged

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #22 on: November 09, 2009, 10:11:08 AM »

Rota RB's FTW

Get bigger injectors.



yeah i got 13x8 w/ 22x8x13 mt slicks for the track, they are sexy for sure.

as for the injectors, i know but i got them for free....well kinda, i gave a buddy of mine some old nasty looking 3" alum. piping that he used to make a intake outta for them....but the used piping was gifted to me and i wasnt ever going to used it, so they were free. im pretty much maxing out the injectors right know. but i have been beating the shit out of it on a daily basis @ 14psi for like 6 months now.
Logged

dvst8r

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3737
  • Unobtainium
Re: scottdh20's project turbo d15b7
« Reply #23 on: November 09, 2009, 11:17:52 AM »

27 posts and no porn. Fail.

On top of this it is 27 posts of JDM faggotry. Things like: it will certainly cause my death 4 point bolt in cage, the gayer then aids hood, the I didn't think it could it get any gayer spoiler,only to be followed by the loving to touch little asain boys sticker. The only thing even remotely redeeming on this whole car, is the manifold and down pipe.

I don't know if the whole internet worth of porn could save this.
Logged
There are two kinds of people: Sheep and sharks. Sharks are winners and they don'#039#039t look back '#039#039cause they don'#039#039t have necks. Necks are for sheep.

scottdh20

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 26
Re: scottdh20's project turbo d15b7
« Reply #24 on: November 09, 2009, 12:26:19 PM »

to c0mpl3x:

sorry i didnt know i could have made these all in one post, every other forum i am on has a picture limit on each post. wont happen again, also just like to say i was a member on the original hmt and i didnt post much but did lots of trolling and loved it. i have been trolling around here for a while aswell as hmt went down hill a while back. just thought i'd post up my build.

yeah my car isnt the fastest but i thought thats what rhmt was all about, yeah a k-swapped civic does run faster with some bolt ons, but i also have like 7-800 into my entire turbo kit on a d15b7 that can  run mid to high 13's, and low 13's after i swap in a si tranny.

i ran a 14.3 @ 98mph with a 1.9 60ft. it was 45* out and the track wasnt prepped for shit, the first 60-100 ft were prepped very well though. 2nd was spinning like crazy with slicks. im not making excuses but it is what it is. so i have a low 14 sec car

to dvst8r

whats wrong with autopower roll bars? i have seen them on many builds and as far as bolt-in cages go are the only ones i would trust my life with. i get alot of shit for the hood, whatever i like it, its my car not yours, and its functional, my water temps dropped nearly 20* and my under hood temps are way cooler. sorry function > form, sorry your not a fan of the spoiler i like it. ahgain this is my car and i'm building it per my taste, i dont need your aprovel nor anybody elses.

as for the porn, sorry do admit fault there my bad, but i am at work :)
Logged

crxvtec91

  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 8343
  • RIP old hmt. SloS13 for King!!!
Re: scottdh20's project turbo d15b7
« Reply #25 on: November 09, 2009, 01:25:33 PM »

I fix some of it, now do the rest!
Logged
My build thread; http://www.realhomemadeturbo.com/forum/index.php?topic=2444.0


I like my girls like I like my cars, rich and retarded.

dvst8r

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3737
  • Unobtainium
Re: scottdh20's project turbo d15b7
« Reply #26 on: November 09, 2009, 02:42:46 PM »


to dvst8r

whats wrong with autopower roll bars? i have seen them on many builds and as far as bolt-in cages go are the only ones i would trust my life with.

Bolt in roll bars are more likely to end your life then save it. I don't care if they are used in a million builds, there is a reason no sanctioning body anywhere in the world approves their use.
Logged
There are two kinds of people: Sheep and sharks. Sharks are winners and they don'#039#039t look back '#039#039cause they don'#039#039t have necks. Necks are for sheep.

brine04

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2251
  • B-North
Re: scottdh20's project turbo d15b7
« Reply #27 on: November 09, 2009, 02:55:50 PM »

Needs porn, more injector, less xenocron and that man size turbo is an hx52 UrbanIndian runs one.
Logged
92GSR - mild interest

boostinallday

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 77
Re: scottdh20's project turbo d15b7
« Reply #28 on: November 09, 2009, 08:30:52 PM »

i ran a 14.0 on a stock 199k miles z6 on 10 psi  but good start iguess.
Logged

SloS13

  • RHMT Ex-President
  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: I am a geek!!
  • My avatar is broken
Re: scottdh20's project turbo d15b7
« Reply #29 on: November 09, 2009, 09:18:26 PM »

holy fucking shit what's going on in this thread.

5 pics and 1 vid would have done fine.  roll cage and slicks on a 14 second car?
Logged
Pages: [1] 2   Go Up