:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Official RHMT TANK! that's right i said a TANK! (link)

Pages: [1]   Go Down

Author Topic: thinking of making a groove for a copper wire on a 38mm WG flange  (Read 4983 times)

DSharp

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 407
thinking of making a groove for a copper wire on a 38mm WG flange
« on: April 03, 2017, 08:21:18 PM »
ok so i have an adapter like this


Gonna open up the id of the two flanges to match the pipe id, going to open it up from 1.500 to 1.610.  Shitty part is the ID of all the flange gaskets I have are smaller than the id of the flanges I think they are around 1.4"
I figured i might machine a ring groove in the adapter's flange and use a piece of cut and filed copper wire as the gasket.  Also been thinking of turning a continuous aluminum ring, but aluminum will be getting real damn soft at those temps.

Any of you fuckers ever done anything like this?
Logged
No escape from the mass mind rape

crxvtec91

  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 8343
  • RIP old hmt. SloS13 for King!!!
Re: thinking of making a groove for a copper wire on a 38mm WG flange
« Reply #1 on: April 04, 2017, 09:07:36 AM »
I would just run it and see what it does
Logged
My build thread; http://www.realhomemadeturbo.com/forum/index.php?topic=2444.0


I like my girls like I like my cars, rich and retarded.

DSharp

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 407
Re: thinking of making a groove for a copper wire on a 38mm WG flange
« Reply #2 on: April 04, 2017, 02:23:59 PM »







It will either be brilliant or it will leak.  Let's find out.
Logged
No escape from the mass mind rape

DSharp

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 407
Re: thinking of making a groove for a copper wire on a 38mm WG flange
« Reply #3 on: April 04, 2017, 06:48:59 PM »






By now your wondering why I machined off the original flange and welded on a new one.  Its because the adapter's flange was like 1/4" smaller than the wastegate flange.  They are supposed to both be the same but that what you get from chinabay parts.  I will also have to machine a new valve seat because the original one was to short to actually seat against the valve from the factory, haha.
Logged
No escape from the mass mind rape

DSharp

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 407
Re: thinking of making a groove for a copper wire on a 38mm WG flange
« Reply #4 on: April 06, 2017, 09:43:03 PM »
Got it done seems ok so far.  Got a new valve seat turned too.



Logged
No escape from the mass mind rape

rawr

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1603
Re: thinking of making a groove for a copper wire on a 38mm WG flange
« Reply #5 on: April 10, 2017, 12:18:01 AM »
looks good
Logged

DSharp

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 407
Re: thinking of making a groove for a copper wire on a 38mm WG flange
« Reply #6 on: April 16, 2017, 09:20:24 PM »
seems to work well.  Boost holds dead flat to redline now
Logged
No escape from the mass mind rape
Pages: [1]   Go Up
« previous next »