:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

ApexSilver06MR/Jason YOU WILL BE MISSED, RIP (link)  :'(

Pages: [1]   Go Down

Author Topic: Cam angle?  (Read 8532 times)

lilpooh21186

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1801
  • B16 Short strokes but holds a high note
Cam angle?
« on: February 07, 2010, 01:59:15 PM »
Will be tuning my first k-series motor I've read alot on the stupid I l-vtec cam angle bs can anyone here give any small tips I shuold follow ? Thanks
Logged
Ecu chipping
basmaps
tuning Dyno/street pm for details
Neptune Dealer PM for RTP details

snm95ls

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3662
Re: Cam angle?
« Reply #1 on: February 07, 2010, 03:39:16 PM »
From what I understand, it is similar to tooning VTAK engagement point.

Do several pulls at different cam phase angles, and optimize the overall powerband with the info you have gathered.

DISCLAIMER:  I have not touched a K series other than an alternator change on a CRV.
Logged

lilpooh21186

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1801
  • B16 Short strokes but holds a high note
Re: Cam angle?
« Reply #2 on: February 07, 2010, 03:42:21 PM »
lol thats what i got from my genral reading
Logged
Ecu chipping
basmaps
tuning Dyno/street pm for details
Neptune Dealer PM for RTP details

Joseph Davis

  • Verbal Assault Technician
  • Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 34733
  • Eugenics prevents retards like widebody93
    • TURBO THIS
Re: Cam angle?
« Reply #3 on: February 07, 2010, 08:15:02 PM »
What are you tuning it on?  Because there are a couple of differences between Hyundaidata and AEM.  If Hyundaidata, are the injectors larger than stock?
Logged

PhilStubbs

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 5885
  • Teh Secksy.....I has it
Re: Cam angle?
« Reply #4 on: February 07, 2010, 08:38:27 PM »
in to hear ideas. i have had a few K guys contact me lately
Logged
obd1>gtgtall

 fucking box started smoking and i saw a flame start up so i grabbed a bucket of water and splashed it on the breaker box.

lilpooh21186

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1801
  • B16 Short strokes but holds a high note
Re: Cam angle?
« Reply #5 on: February 07, 2010, 09:10:26 PM »
Hundyidata civic si kswap in eg chassis 450cc bigger tb I'm and 3in exhaust side cut exit before rear wheel
Logged
Ecu chipping
basmaps
tuning Dyno/street pm for details
Neptune Dealer PM for RTP details

98vtec

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 1076
  • try a warm glass of shut the fuck up
    • BBmoto Tuning
Re: Cam angle?
« Reply #6 on: February 07, 2010, 09:10:38 PM »
read the fukdata tech articles and videos.  If you cant figure it out from there, go off yourself.
Logged
xXx Performance Tuning
-- In House DynoJet
SouthEast Neptune Tuner

lilpooh21186

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1801
  • B16 Short strokes but holds a high note
Re: Cam angle?
« Reply #7 on: February 07, 2010, 09:22:28 PM »
Didn't say I don't understand I'm looking sugestive tips on how to goabout it hence my first time with the program. I'd rather not run into it blind it's easier for me to get tips from someone who uses the program rather tha. Reading the breif comments on it from  the web
Logged
Ecu chipping
basmaps
tuning Dyno/street pm for details
Neptune Dealer PM for RTP details

98vtec

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 1076
  • try a warm glass of shut the fuck up
    • BBmoto Tuning
Re: Cam angle?
« Reply #8 on: February 07, 2010, 09:29:45 PM »
tune fuel and ignition first, then make a composite cam angle map with each pull locked in one cam angle throughout the pull.  Put all the pulls up on the chart and determine where the engine likes the cam angle per RPM range.  Be sure to save the part throttle/mid load cam angle chart and save it in the notepad.  remember it takes time for the cam to advance or retard so you need to remember that when making the composite cam angle map.
Logged
xXx Performance Tuning
-- In House DynoJet
SouthEast Neptune Tuner

lilpooh21186

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1801
  • B16 Short strokes but holds a high note
Re: Cam angle?
« Reply #9 on: February 07, 2010, 09:43:26 PM »
This is the shit I was looki g for that clears it up I was worried valve piston clearance
Logged
Ecu chipping
basmaps
tuning Dyno/street pm for details
Neptune Dealer PM for RTP details

98vtec

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 1076
  • try a warm glass of shut the fuck up
    • BBmoto Tuning
Re: Cam angle?
« Reply #10 on: February 07, 2010, 09:46:12 PM »
Quote from: lilpooh21186 on February 07, 2010, 09:43:26 PM
This is the shit I was looki g for that clears it up I was worried valve piston clearance

its a step by step read on the fukdata tech articles link.  It also has videos.
Logged
xXx Performance Tuning
-- In House DynoJet
SouthEast Neptune Tuner

Joseph Davis

  • Verbal Assault Technician
  • Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 34733
  • Eugenics prevents retards like widebody93
    • TURBO THIS
Re: Cam angle?
« Reply #11 on: February 08, 2010, 12:58:23 AM »
You left out the per-gear fuel trim failure with larger than stock injectors that lets you know it's a poorly cobbled together hack.
Logged

98vtec

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 1076
  • try a warm glass of shut the fuck up
    • BBmoto Tuning
Re: Cam angle?
« Reply #12 on: February 09, 2010, 01:05:25 AM »
Quote from: Joseph Davis on February 08, 2010, 12:58:23 AM
You left out the per-gear fuel trim failure with larger than stock injectors that lets you know it's a poorly cobbled together hack.

i've used kpro once.  My experience is limited.
Logged
xXx Performance Tuning
-- In House DynoJet
SouthEast Neptune Tuner
Pages: [1]   Go Up
« previous next »