Topic: where to buy 3" exhaust fabrication stuff, in the seattle area? (Read 8317 times)

lucas13dourado · « **on:** April 03, 2010, 05:14:55 AM »

I dont post on here much, I want to build a full 3" exhaust for my car (I can weld my own stuff)
and I was wondering where you guys get exhaust piping around the seattle area?
thanks

ApexSilver06MR · « **Reply #1 on:** April 03, 2010, 06:19:45 AM »

Columbia river ftw. They are from oregon.

Or kteller. They make specific exhaust kits for you to weld up.

malichite · « **Reply #2 on:** April 03, 2010, 10:34:29 AM »

acestainless

HiProfile · « **Reply #3 on:** April 03, 2010, 03:08:43 PM »

I bet Buk (jay) could fab you up a full 3", and with a manifold+dp to match.

bigwig · « **Reply #4 on:** April 03, 2010, 03:10:39 PM »

Vrsexhaust is dirty cheap. I believe they still are in business. Figure another $40-50 for shipping.

bigdaddyvtec · « **Reply #5 on:** April 03, 2010, 03:31:10 PM »

Call stephan at ASP. Hes in Kent and will have ANYTHING you need IN STOCK, tell him Spiker Josh and Randy reffered you.

ADVANCED STREET PERFORMANCE.

http://advancedstreetperformance.com/

Good to see you again nog, cant wait to see you at the dyno... in all your VW gay pride lol....

lucas13dourado · « **Reply #6 on:** April 03, 2010, 03:49:16 PM »

I want to try this on my own, Im getting decent at tig, welding.
Ill check those places out and see..

thanks a lot guys

ratcityrex · « **Reply #7 on:** April 03, 2010, 03:53:33 PM »

this flange is sex

lucas13dourado · « **Reply #8 on:** April 04, 2010, 06:42:49 AM »

Ok Im going to buy the stuff from columbia river... what do you guys go with as far parts?
Im thinking about doing this:

-3.00" OD, 6.00" Radius, 16 Gauge, 304 Stainless Ultimate BK
-3.00" ID x 4.00" Long, Stainless Flex Tube
- 5x 3.00" Mild V-Band Flange
- 3x 02 sensor bungs
which comes to 416$ + shipping. (I know the discount code, but I dont know where to apply it?)

also, is 16 gauge thick enough for the whole exhaust?

CSaddict · « **Reply #9 on:** April 04, 2010, 07:01:27 AM »

What kind of car? I would seriously give VRS a chance. They supply Kteller. For that much money they may have a nice mandrel bent kit in stainless for less.

narfdanarf · « **Reply #10 on:** April 04, 2010, 11:19:25 AM »

16 gauge is plenty big enough

why are you getting 5 vbands and 3 o2 bungs though that is the real fucking question.

Corey · « **Reply #11 on:** April 04, 2010, 12:01:17 PM »

Quote from: narfdanarf on April 04, 2010, 11:19:25 AM

16 gauge is plenty big enough

why are you getting 5 vbands and 3 o2 bungs though that is the real fucking question.

2 oem oxygen sensors + wideband. obvious answer

lucas13dourado · « **Reply #12 on:** April 04, 2010, 12:34:54 PM »

Quote from: Corey on April 04, 2010, 12:01:17 PM

Quote from: narfdanarf on April 04, 2010, 11:19:25 AM
16 gauge is plenty big enough

why are you getting 5 vbands and 3 o2 bungs though that is the real fucking question.

2 oem oxygen sensors + wideband. obvious answer

exactly

the car is a 99 passat... I need 1 v-band at the turbo, 2 for the downpipe and 2 for the rear section of the car
I could just use regular exhaust clamps but I dont want to deal with gaskets

lucas13dourado · « **Reply #13 on:** April 04, 2010, 12:51:07 PM »

I have a hard time navigating through VRSs website, and havent found any tubing kits that are not manufacturer specific?

ryan89crx · « **Reply #14 on:** April 04, 2010, 12:52:59 PM »

noobs...
http://www.vrsexhaust.com/TUBING_KITS/tubing_kits.html

VRS is where I get all my exhaust

lucas13dourado · « **Reply #15 on:** April 04, 2010, 01:08:54 PM »

Quote from: ryan89crx on April 04, 2010, 12:52:59 PM

noobs...
http://www.vrsexhaust.com/TUBING_KITS/tubing_kits.html

VRS is where I get all my exhaust

like I said "that is not manufacturer specific"

ryan89crx · « **Reply #16 on:** April 04, 2010, 01:17:42 PM »

http://www.vrsexhaust.com/BENDS/bends.html

If you just want a bunch of random bends thrown together, hit up Columbia River Mandrel Bends

Eggylshatch · « **Reply #17 on:** April 05, 2010, 02:00:33 AM »

stainless is too ballur for me... I'd just buy mild and paint it with a high temp paint. but thats just me

ryan89crx · « **Reply #18 on:** April 05, 2010, 01:31:42 PM »

Quote from: Eggylshatch on April 05, 2010, 02:00:33 AM

stainless is too ballur for me... I'd just buy mild and paint it with a high temp paint. but thats just me

Same here

bigwig · « **Reply #19 on:** April 05, 2010, 01:38:28 PM »

You might be able to ask to use ss409. It's stainless basically used for automotive exhausts. It's priced right between mild steel and 304.

ratcityrex · « **Reply #20 on:** April 05, 2010, 01:43:32 PM »

Fuck I just stole my brother-in-laws old 3" injen exhaust off of his srt4 and cut that shit up and re-welded it to fit the crx. Worked good for me. Check out cl and see if anyone is selling some old stainless exhaust off of a XXX brand car and cut that shit up and make it work. DO WORK S0N!!

j.h.christ · « **Reply #21 on:** April 05, 2010, 01:55:39 PM »

http://seattle.craigslist.org/sno/pts/1676035550.html

pow!

News:

Author Topic: where to buy 3" exhaust fabrication stuff, in the seattle area? (Read 8317 times)

bigwig

bigwig