:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Jay & Trevor YOU WILL BE MISSED, RIP  :'(

Pages: [1]   Go Down

Author Topic: chinese forged rods?  (Read 10652 times)

turbohf

  • aka: the rHMT Jew
  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 9712
  • Overkill is Underrated
chinese forged rods?
« on: July 11, 2013, 01:47:57 PM »
anyone have some first hand experience with these? there are a hole bunch of H and I beam rods on eBay with bolts for as low as 240bucks.

just worried about the finish work and how well they are machined. don't want to bolt them down and they just clamp down on the crank and not spining a bearing at startup. or piston rattling around on the small end lol.
Logged
Dustin  :Jew:
1987 Buick Regal Limited 6.0L/4L80E (LQ4, 862 heads, tbss intake, 92mm tb, e1841p cam, Holley EFI)
2000 Silverado LS 5.3L Reg Cab Short Bed
1966 Chevy II Nova 400 4dr Sedan V8


'Faster, Faster, until the thrill of speed overcomes the fear of death.'

Minor Threat

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2401
Re: chinese forged rods?
« Reply #1 on: July 11, 2013, 06:12:33 PM »
I've run em in 2 cars, no issues. I had my engine builder look em over, they were both in spec.
Logged
"quotquotand the welds look like a pigeon had 1 too many chili-dogs, whoever built them needs to go throw their tools in the ocean."quotquot

www.facebook.com/enhancedautoperformance

79fairmont

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1709
Re: chinese forged rods?
« Reply #2 on: July 11, 2013, 10:02:49 PM »
Usually the require some pin fitting. They seem to run on the small side most of the time.
Logged

turbohf

  • aka: the rHMT Jew
  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 9712
  • Overkill is Underrated
Re: chinese forged rods?
« Reply #3 on: July 11, 2013, 10:21:23 PM »
more concerned about the fit of the big end. good to note the small end. i think i did that for my TunerToys rods also. i would really hate for the big end to be too tight and seize up/spin bearings.

i will probably end up jewing someone tough on some eagle/manleys. but if that fails might just throw these in.


http://www.ebay.com/itm/Honda-Acura-B18A-B-B20B4-CRV-DOHC-SFI-Integra-H-Beam-Connecting-Rods-4PCS-Bolts-/271047064726?pt=Motors_Car_Truck_Parts_Accessories&hash=item3f1ba9fc96&vxp=mtr
not even arps in those ones.

http://www.ebay.com/itm/GSP-GSR-TYPE-R-B18C-DA-DC2-EF-EG-EK-NA-TURBO-FORGED-BEAM-ROD-RODS-W-BOLTS-DOHC-/380449981682?pt=Motors_Car_Truck_Parts_Accessories&hash=item58949604f2&vxp=mtr
dont look to bad in those pics....
Logged
Dustin  :Jew:
1987 Buick Regal Limited 6.0L/4L80E (LQ4, 862 heads, tbss intake, 92mm tb, e1841p cam, Holley EFI)
2000 Silverado LS 5.3L Reg Cab Short Bed
1966 Chevy II Nova 400 4dr Sedan V8


'Faster, Faster, until the thrill of speed overcomes the fear of death.'

jdmhatchracer94

  • I have a nova that will never run!!
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2264
  • Official RHMT Nigglet!
Re: chinese forged rods?
« Reply #4 on: July 11, 2013, 11:08:11 PM »
Buddy used the SGI brand rods $225 with ARP 2000 bolts. Have now been in three engines still going strong. Remember the TT rods were china and they held still hold up for people
Logged
4 door eg nbspnbsp 13.2@118 someone needs to run slicks
338hp 293tq

Good enough to fuck your mother

turbohf

  • aka: the rHMT Jew
  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 9712
  • Overkill is Underrated
Re: chinese forged rods?
« Reply #5 on: July 12, 2013, 12:17:03 AM »
also, remember that your EAGLE rods are made in china... finish machined in US...  :-*
Logged
Dustin  :Jew:
1987 Buick Regal Limited 6.0L/4L80E (LQ4, 862 heads, tbss intake, 92mm tb, e1841p cam, Holley EFI)
2000 Silverado LS 5.3L Reg Cab Short Bed
1966 Chevy II Nova 400 4dr Sedan V8


'Faster, Faster, until the thrill of speed overcomes the fear of death.'

jdmhatchracer94

  • I have a nova that will never run!!
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2264
  • Official RHMT Nigglet!
Re: chinese forged rods?
« Reply #6 on: July 12, 2013, 02:27:33 AM »
Exactly
Logged
4 door eg nbspnbsp 13.2@118 someone needs to run slicks
338hp 293tq

Good enough to fuck your mother

92CXyD

  • Twincharged Smeghead
  • Global Moderator
  • Certified OG
  • *****
  • Online Online
  • Posts: 6845
  • I look around and all I see is Smegheads
Re: chinese forged rods?
« Reply #7 on: July 12, 2013, 08:12:56 AM »
Quote from: jdmhatchracer94 on July 11, 2013, 11:08:11 PM
Buddy used the SGI brand rods $225 with ARP 2000 bolts. Have now been in three engines still going strong. Remember the TT rods were china and they held still hold up for people

I've used two sets, one of them were TunerToys and the other was some lowball eagles.

I'm using a set of cunninghams and they a little lighter and look like they are of better quality.

I also just bought a set crower d15 rods and they also look more trust worthy than the CDM rods.

CDM rods I would just have the big ends checked out to make sure concentric.  :noel:
Logged
Pages: [1]   Go Up
« previous next »