:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Official RHMT TANK! that's right i said a TANK! (link)

Pages: [1]   Go Down

Author Topic: best way to get a snap ring on and off the Holset HX35 compressor housing  (Read 12674 times)

marcj

  • Marc Jew
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1956
  • Never alone, Never again. (NA)
best way to get a snap ring on and off the Holset HX35 compressor housing
« on: October 04, 2009, 12:20:04 PM »
I've done it once before, and never wished to do it again (using channel lock pliers). Taking the ring out obviously is the easiest by all means, but putting it back in was pretty ridiculous with the pliers I have) Does anyone have a better method? I know cummins has a tool for it (snap ring pliers?). any advice is appreciated as usual  :)
Logged

brine04

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2251
  • B-North
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #1 on: October 04, 2009, 12:40:18 PM »
I use the overpriced snap on locking snap ring pliers.
Logged
92GSR - mild interest

TTC

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1786
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #2 on: October 04, 2009, 01:21:53 PM »
A few years ago i got a 14b.  I tried to remove the damned snap ring without proper tools.  We welded spikes toa pair of vicegrips and with some fucking around i got them on and off.  Last month i bought some channel lock reversible snap ring pliers.  I wanted to cockpunmch myself for waiting this long to get them, instead of fucking around with a giant ring for 50minutes it took 5.

Spend the 30bux, get a really good set and you'll love life.
Logged

patsmx5

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1584
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #3 on: October 04, 2009, 01:31:00 PM »
+1 for getting a GOOD set. I had an autozone special set and they sucked balls. Now I got Craftsman's and they're pretty good. Never mess with snap rings without the piers. A good set comes with a lot of different tip sizes, angled tips, etc. so you can get in at weird angles. Only way to do snap rings.
Logged
Quote: Originally Posted by Adam Hopkins
There is no such thing as too much boost. You could have too little rod, piston, or sleeve. But never too much boost.

E-b0la

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2276
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #4 on: October 04, 2009, 09:46:18 PM »
just buy snap ring pliers
Logged

Tim

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2632
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #5 on: October 04, 2009, 11:39:55 PM »
Quote from: c0mpl3x on October 04, 2009, 06:43:52 PM
weld 2 washers to it

install a 3" long section of allthread or a mostly threaded 1/4-20 bolt, and a nut

tighten it on turbo, loosen nut to seat into comp housing
+1
Blaast welded washers on to mine and they're my only hope when the turbo is on the car.
I couldn't see buying a massive set of pliers I'd never use on anything else being easier. That fucker is huge
Logged

oinesra

  • Guest
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #6 on: October 16, 2009, 10:39:20 PM »
On my schwitzer I was able to take it off with 2 roofing nails and plyers.

But dude their is a harbour frieght like 10 min from you. Just give them a 5dollar food sstamp and you can get a 137 piece snapring plyer set.
Logged

turbowagonman

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 5
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #7 on: October 22, 2009, 03:47:22 PM »
iv'e not found any snapring pliers big enough for that snapring. I use two pair if standard visegrips. I use one to hold the snapring in the groove on one side near the end, and grab the other tab and tweak it out, then pop the other visegrip off. kindof the same way to get it back in. my snapring had one side broke off when I started, so thats how I figured out how to do it that way.
Logged

ryan89crx

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3228
  • 20lbs of love!
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #8 on: October 22, 2009, 06:44:58 PM »
my hx35 had both holes for snap ring pliers, as well as tabs that pointed up which you could use a pair of pliers on. i just used channellocks and it came off just fine
Logged
d-series on 20 pounds will turn you out!

SloS13

  • RHMT Ex-President
  • Administrator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: I am a geek!!
  • My avatar is broken
Re: best way to get a snap ring on and off the Holset HX35 compressor housing
« Reply #9 on: October 22, 2009, 06:51:06 PM »
With a little modification, these work awesome on 14b's

Logged
Pages: [1]   Go Up
« previous next »