:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Jay & Trevor YOU WILL BE MISSED, RIP  :'(

Pages: [1]   Go Down

Author Topic: faster or better way of lapping valves??  (Read 8772 times)

ryan1

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
faster or better way of lapping valves??
« on: October 31, 2009, 05:01:53 PM »
does anyone know a faster or better way of lapping valves than with a suction cup style of tool.
the cup keeps falling off/not sticking to well. i have seen people get away with hooking a drill up to the valve stem but i don't have enough room dohc mazda bp motor.
not going to the mach. shop either im on a budget, using grinding stones (old sckool way) the stones would interfer with the head.
Logged

patsmx5

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1584
Re: faster or better way of lapping valves??
« Reply #1 on: October 31, 2009, 05:04:40 PM »
clean the valve, then put some oil on it and the cup, then when you stick it on there it won't fall off. Cut the tool in half and chuck it up in a drill.
Logged
Quote: Originally Posted by Adam Hopkins
There is no such thing as too much boost. You could have too little rod, piston, or sleeve. But never too much boost.

ryan1

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
Re: faster or better way of lapping valves??
« Reply #2 on: October 31, 2009, 07:33:09 PM »
Quote from: patsmx5 on October 31, 2009, 05:04:40 PM
clean the valve, then put some oil on it and the cup, then when you stick it on there it won't fall off. Cut the tool in half and chuck it up in a drill.

yeah i did clean them, i will try a little oil and and cut the tool too.
have you done it this way?
Logged

Atticus

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 1329
Re: faster or better way of lapping valves??
« Reply #3 on: October 31, 2009, 08:15:06 PM »
rubber hose and a drill on low speed from the back side. 
make sure the valve stem is clean has no compound on it and has lots of lube so that you dont fuck up the guide.
Logged

Turbo hondas are like crack, you can say no for a little while but one day your gonna have to hit up Tyrone on the corner for a t3/t4.

ryan89crx

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3228
  • 20lbs of love!
Re: faster or better way of lapping valves??
« Reply #4 on: October 31, 2009, 09:16:56 PM »
i just hacked off the head of a bolt and put it in my drill with the suction cup stuck on the end.

worked like a fucking champ


Logged
d-series on 20 pounds will turn you out!

Corey

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3030
Re: faster or better way of lapping valves??
« Reply #5 on: October 31, 2009, 10:44:21 PM »
i like ryans idea, im gonna try that on my next valve job.

i always used a piece of stiff vacuum hose, slid it on the end of the valve stem and slipped it over a piece of round rod that was in the drill.
Logged

highroller54

  • I caught the fable Novacorn
  • RHMT Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 10831
  • Spreading the rhmt word like PB&J
Re: faster or better way of lapping valves??
« Reply #6 on: October 31, 2009, 11:51:34 PM »
it should not require that much lapping.  :?:
Logged
Xenocron is a piece of shit.

I solve my problems like an adult, at the strip club drinking on a work night. http://www.competitiondiesel.com/forums/images/smilies/turbo1.gif

t_cel_t

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3147
Re: faster or better way of lapping valves??
« Reply #7 on: November 01, 2009, 01:51:34 AM »
Quote from: highroller54 on October 31, 2009, 11:51:34 PM
it should not require that much lapping.  :?:
ive only done it on lawn mowers but it only took me about 1 min to get each valve perfect. maybe a couple hundred revolutions of the valve was it.
Logged
malone labe

I think all cop cars need to have turbo. nbspnbsp Then they would understand the necessity of putting your foot down and how uncontrollable the urge is to fucking rail on that shit.

ryan1

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
Re: faster or better way of lapping valves??
« Reply #8 on: November 02, 2009, 01:33:03 AM »
thanks for the replys, yes valves and seats usually don't need a super lot of lapping but when your
using a hand tool to lap ( starting a fire with a stick style movements) it's kind of hard to be stedy and the suction cup want to fall off a lot.
this morning before football started i did the cut a old head bolt or anykind of bolt and put the suction cup on there then threw it in the drill, it worked very well and i could steady it with a finger from my left hand and the cup would not fall off as much and i kept the drill speed low and it work great.
Logged

ifly87

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 294
Re: faster or better way of lapping valves??
« Reply #9 on: November 02, 2009, 03:21:26 AM »
Yeah if you lap them too much you will basically sand out the interference angle ground into the valve/seat. All they should need is a few twists by hand.
Logged
Sorry dirtyturbopantyripper, you are banned from using this forum!
You are banned! K Series >gtgt D Series

Lol...Fags

Joseph Davis

  • Verbal Assault Technician
  • RHMT Moderator
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 34733
  • Eugenics prevents retards like widebody93
    • TURBO THIS
Re: faster or better way of lapping valves??
« Reply #10 on: November 02, 2009, 08:57:54 AM »
Quote from: highroller54 on October 31, 2009, 11:51:34 PM
it should not require that much lapping.  :?:

Yup, if the bluing you put on the valve face doesn't go away immediately you might want to send the works off to the machine shop.
Logged
Pages: [1]   Go Up
« previous next »