Topic: Bandsaw blades (Read 20677 times)

malichite · « **on:** February 09, 2010, 03:17:44 PM »

I have been ordering blades from grizzly and they have been ok. What do you guys use? Is there something better out there? I have been running 64 1/2 14-18 raker for stainless and mild steel. Just ordered up a raker 14 tpi and a raker 18 tpi non variable to see if they are any different but just grizzly blades. The last one I had just didn't seem to last that long.

patsmx5 · « **Reply #1 on:** February 09, 2010, 03:21:39 PM »

Cutting stainless is a bitch on blades. I would make sure you're not running the blade too fast. Too much heat will anneal the blade and then it goes to shit.

weirtech · « **Reply #2 on:** February 09, 2010, 04:12:47 PM »

cut with some coolant. also break your blade in on something softer like mild or aluminum for a couple laps.

i get my blades made locally.

malichite · « **Reply #3 on:** February 09, 2010, 04:29:07 PM »

I will have to try breaking them in. I run the saw on the slowest setting I can for stainless. Blade doesnt get hot or really even warm while cutting. I have played with shooting a little wd on the blade but have not done a full cooling setup yet. I really need to mock something up.

CSaddict · « **Reply #4 on:** February 09, 2010, 04:54:54 PM »

I use just about any brand Grainger is carrying at the time. Morse, Starret, whatever. I always use the 14-18 variable raker and I have had good luck with them. Run them medium speed and keep the saw tensioned on the spring to not over heat them.

malichite · « **Reply #5 on:** February 09, 2010, 05:07:58 PM »

what are the grainger blades running you price wise? they are about $25 from grizzly.

CSaddict · « **Reply #6 on:** February 09, 2010, 05:16:22 PM »

About the same. The last I bought was $23 I believe.

CSaddict · « **Reply #7 on:** February 09, 2010, 05:18:24 PM »

Just got an updated price of $28.xx Matrix II bi metal with cobalt.

malichite · « **Reply #8 on:** February 09, 2010, 05:18:26 PM »

cool. I am getting tired of these grizzly blades. The last one I bought was bent at the weld and would lift up everytime that part came across the cut. Blade didn't last long. I should have complained before I broke it but I procrastinated.

CSaddict · « **Reply #9 on:** February 09, 2010, 05:25:33 PM »

We have all had our share of those. Corey had a bunch of defective blades.

turbob16hatch · « **Reply #10 on:** February 09, 2010, 06:29:15 PM »

I buy blades from acme tool crib in my town, there resonable on price around 25-30 and last a long time. there made in house so you can get them in any length ya need.

7808 · « **Reply #11 on:** February 09, 2010, 06:37:01 PM »

i buy mine at menards (morse) or any other local place. there always like $8 for a 64 1/4" 14tpi but my 1950 ?menards bandsaw which looks just like the one they sell at HF fucks blades up like nothin cause its so sloppy

Corey · « **Reply #12 on:** February 10, 2010, 01:15:50 AM »

you guys might not believe me but ive been using the harbor frieght brand (central machinery i think?) bimetals that are 16.99 in store for the last year.

i shit you not they are the best blades i have used thus far. they last longer then starrett or lenox and cut just as well.

dont believe me? try it.

ive had 1 blade break on me right away, and harbor frieght asked no questions just told me to grab another one. the last blade i just changed was on for so long it was missing half the teeth and it was still cutting like a champ.

Toysrme · « **Reply #13 on:** February 10, 2010, 03:14:33 PM »

Buy a spool, weld them together. grind the weld down & hit it with a torch so itll be flexible

PhilStubbs · « **Reply #14 on:** February 10, 2010, 07:23:30 PM »

HF blades go to shit quick for me, home depot blades for $16 last me quite a while though. at least 3x as long as the HF

Corey · « **Reply #15 on:** February 10, 2010, 11:07:44 PM »

Quote from: SecksyPeePee on February 10, 2010, 07:23:30 PM

HF blades go to shit quick for me, home depot blades for $16 last me quite a while though. at least 3x as long as the HF

are you using the bimetal ones in the blue and yellow package?

the homodepot ones are fuckin trash they are not bimetal.

PhilStubbs · « **Reply #16 on:** February 10, 2010, 11:10:39 PM »

I always buy bi-metal no matter where I get it even home depot.

Corey · « **Reply #17 on:** February 10, 2010, 11:12:10 PM »

Quote from: SecksyPeePee on February 10, 2010, 11:10:39 PM

I always buy bi-metal no matter where I get it even home depot.

ive never seen a bimetal blade at HD. would be nice if they had them so i could grab one in a pinch cause theres a HD down the street from my shop.

PhilStubbs · « **Reply #18 on:** February 11, 2010, 07:52:30 AM »

i am about due for a new blade. i will post a pic of the packaging. maybe its a regional thing, im in FL.

i am really considering getting one of those blade welders at HF and making my own from now on. seems like it would be a lot cheaper

Passenger · « **Reply #19 on:** February 12, 2010, 08:36:26 PM »

Wikus bandsaw blades are top notch. Lennox has gone down with the quality big time in the last year, we used to use a lot of them.

PhilStubbs · « **Reply #20 on:** February 12, 2010, 10:12:30 PM »

Here is what I get from homedepot. I usually use 18tpi not 14, but that was a quick search

jay · « **Reply #21 on:** February 13, 2010, 01:58:11 AM »

what band saw do you guys own?

PhilStubbs · « **Reply #22 on:** February 13, 2010, 08:19:46 AM »

jay · « **Reply #23 on:** February 13, 2010, 12:21:16 PM »

Quote from: SecksyPeePee on February 13, 2010, 08:19:46 AM

HF

have you had anything break on it or had to replace any parts?

is it true they have a 90 day no hassle replacement warranty

PhilStubbs · « **Reply #24 on:** February 13, 2010, 01:52:20 PM »

i dont know about the warranty. i have have mine for 6-7 years without a single issue. thinking about buying another to make a stand up bandsaw. i hate converting mine back and forth and real stand up units cost too much

turbob16hatch · « **Reply #25 on:** February 14, 2010, 12:46:41 AM »

I use mine more as a vertical bandsaw lately, and it is annoying to raise it up. I wish they made a mid sized vertical. All i see are small wood bandsaws then the large metal saws, nothing in between.

jay · « **Reply #26 on:** February 14, 2010, 02:03:02 AM »

sorry stupid question

when do you cut with it in the vertical position and when do you cut in the horizontal position?

vertical = slide what your cutting through the blade?

horizontal = drop down the blade onto what your cutting like a chop saw?

i feel stupid...

PhilStubbs · « **Reply #27 on:** February 14, 2010, 02:04:55 AM »

Home depot sells a nice upright wood saw for $100 or so I am considering getting and changing the gearing for wood. I had one for a short time and considered doing it, but I returned it cause I needed something else at the time.

Yea Buk, that's pretty much it.

jay · « **Reply #28 on:** February 17, 2010, 06:16:16 PM »

k so im off to harbor freight to pick up a band saw and the blue flame welding helmet lol

CSaddict · « **Reply #29 on:** February 17, 2010, 06:20:19 PM »

Buk buy a bi-metal for that saw while you are there. The one it comes with is a piece of shit.

News:

Author Topic: Bandsaw blades (Read 20677 times)