Topic: cummins discussion thread. (Read 136852 times)

chris · « **Reply #150 on:** March 09, 2010, 10:22:28 PM »

Buy a mig welder!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

ryan89crx · « **Reply #151 on:** March 10, 2010, 01:43:15 AM »

Quote from: chris M on March 09, 2010, 10:22:28 PM

Buy a mig welder!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

That's how I make my manifolds

Although I'm sure nobody would PAY for one

96turboracer · « **Reply #152 on:** March 10, 2010, 02:07:08 AM »

Quote from: CSaddict on March 09, 2010, 06:25:24 PM

Worth every penny.

Agreed.

I love my Econotig. I've been using it for about three years now, bought it used, and it's always worked great!

That sheet is really confusing me about the amperage control dial, because it absolutely changes all of my aperage settings when using the TIG function

Anyway, hopefully you'll get the welder back with a minimum of cost involved.

jay · « **Reply #153 on:** March 10, 2010, 06:37:08 PM »

Quote from: 96turboracer on March 10, 2010, 02:07:08 AM

Quote from: CSaddict on March 09, 2010, 06:25:24 PM

Worth every penny.

Agreed.

I love my Econotig. I've been using it for about three years now, bought it used, and it's always worked great!

That sheet is really confusing me about the amperage control dial, because it absolutely changes all of my aperage settings when using the TIG function

Anyway, hopefully you'll get the welder back with a minimum of cost involved.

apparently it didnt effect it on older econotigs only on the newer ones?

fuck it...

its now past 5... and i didnt get a call today so maybe tomorrow...

jay · « **Reply #154 on:** March 11, 2010, 11:35:28 AM »

?

http://cgi.ebay.com/VICTOR-ARGON-FLOW-METER_W0QQitemZ260564873476QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item3caae07104

dvst8r · « **Reply #155 on:** March 11, 2010, 12:06:07 PM »

Quote from: jay on March 11, 2010, 11:35:28 AM

?

http://cgi.ebay.com/VICTOR-ARGON-FLOW-METER_W0QQitemZ260564873476QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item3caae07104

If it works, and doesn't leak. Yes, that will do donkey, that will do.

BenDover · « **Reply #156 on:** March 11, 2010, 01:28:52 PM »

Quote from: dvst8r on March 11, 2010, 12:06:07 PM

Quote from: jay on March 11, 2010, 11:35:28 AM
?

http://cgi.ebay.com/VICTOR-ARGON-FLOW-METER_W0QQitemZ260564873476QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item3caae07104

If it works, and doesn't leak. Yes, that will do donkey, that will do.

+1 They usually crack at the top of the glass because dumbasses open the valve full pressure

bigdaddyvtec · « **Reply #157 on:** March 11, 2010, 05:12:08 PM »

buk9tp · « **Reply #158 on:** March 11, 2010, 10:30:33 PM »

a k m

jay · « **Reply #159 on:** March 12, 2010, 03:20:54 AM »

Quote from: bigdaddyvtec on March 11, 2010, 05:12:08 PM

AKM

wat

t_cel_t · « **Reply #160 on:** March 12, 2010, 03:44:14 AM »

avtomat kalashnikov moderna

chris · « **Reply #161 on:** March 12, 2010, 06:54:05 AM »

Quote from: ryan89crx on March 10, 2010, 01:43:15 AM

Quote from: chris M on March 09, 2010, 10:22:28 PM
Buy a mig welder!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
That's how I make my manifolds

Although I'm sure nobody would PAY for one

Mig welder is great can take anywhere and can do general repair exhaust work in no time. Buk doesnt get that the few people who make a living at performance stuff are fuckin on another level with ungodly amount of years behind them. Not to mention most were around old school motorheads who taught them the ropes.

glustic · « **Reply #162 on:** March 12, 2010, 04:36:08 PM »

Quote from: chris M on March 12, 2010, 06:54:05 AM

Quote from: ryan89crx on March 10, 2010, 01:43:15 AM
Quote from: chris M on March 09, 2010, 10:22:28 PM
Buy a mig welder!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
That's how I make my manifolds

Although I'm sure nobody would PAY for one

Mig welder is great can take anywhere and can do general repair exhaust work in no time. Buk doesnt get that the few people who make a living at performance stuff are fuckin on another level with ungodly amount of years behind them. Not to mention most were around old school motorheads who taught them the ropes.

Chris! You are crushing buks dreams!!! How dare you sir!
We all would like to see more fail

NoPistons! · « **Reply #163 on:** March 12, 2010, 04:58:42 PM »

I didn't feel like going through all 6 pages. The first pictures on page 1 and then seeing it was a fucking tig?

HOW DO YOU SUCK THAT BAD? It looks like you're trying to weld with a plasma cutter using dogshit as filler. Fuck.

I read page six. Your welder is FUUUUUUUCKED. Really. The first time i jumped on a tig machine i could run a bead. It looked like flux core because i didn't use enough heat but yeah....it wasn't burning through with a crazy ass ark

I alwasy use NEEDLE SHARP tungsten when i weld steel and i ball it up when i use aluminum.

I also used red for steel and green for aluminum.

I'm so ready for my tig welder...... Already have my 220v cords, breakers and concrete ready for the shop to get dropped off..... Just gotta get on my down payment and i'll be pumping out exhausts, manifolds and stuff like that for friends.

t_cel_t · « **Reply #164 on:** March 12, 2010, 05:05:24 PM »

its a little different when you have never seen someone tig in person.

turbob16hatch · « **Reply #165 on:** March 12, 2010, 06:57:36 PM »

Quote from: NoPistons! on March 12, 2010, 04:58:42 PM

I didn't feel like going through all 6 pages. The first pictures on page 1 and then seeing it was a fucking tig?

HOW DO YOU SUCK THAT BAD? It looks like you're trying to weld with a plasma cutter using dogshit as filler. Fuck.

I read page six. Your welder is FUUUUUUUCKED. Really. The first time i jumped on a tig machine i could run a bead. It looked like flux core because i didn't use enough heat but yeah....it wasn't burning through with a crazy ass ark

I alwasy use NEEDLE SHARP tungsten when i weld steel and i ball it up when i use aluminum.

I also used red for steel and green for aluminum.

I'm so ready for my tig welder...... Already have my 220v cords, breakers and concrete ready for the shop to get dropped off..... Just gotta get on my down payment and i'll be pumping out exhausts, manifolds and stuff like that for friends.

Buk v2?

Joseph Davis · « **Reply #166 on:** March 12, 2010, 07:00:18 PM »

Quote from: turbob16hatch on March 12, 2010, 06:57:36 PM

Quote from: NoPistons! on March 12, 2010, 04:58:42 PM
I didn't feel like going through all 6 pages. The first pictures on page 1 and then seeing it was a fucking tig?

HOW DO YOU SUCK THAT BAD? It looks like you're trying to weld with a plasma cutter using dogshit as filler. Fuck.

I read page six. Your welder is FUUUUUUUCKED. Really. The first time i jumped on a tig machine i could run a bead. It looked like flux core because i didn't use enough heat but yeah....it wasn't burning through with a crazy ass ark

I alwasy use NEEDLE SHARP tungsten when i weld steel and i ball it up when i use aluminum.

I also used red for steel and green for aluminum.

I'm so ready for my tig welder...... Already have my 220v cords, breakers and concrete ready for the shop to get dropped off..... Just gotta get on my down payment and i'll be pumping out exhausts, manifolds and stuff like that for friends.

Buk v2?

Buk v0.7

jundoc · « **Reply #167 on:** March 12, 2010, 10:15:02 PM »

i didnt read all posts...but what kind of gas are you using...should be using argon....thats what we use in our shop....looks like its a gas issue....just my 2 cents...

jay · « **Reply #168 on:** March 13, 2010, 01:28:22 AM »

Quote from: jundoc on March 12, 2010, 10:15:02 PM

i didnt read all posts...but what kind of gas are you using...should be using argon....thats what we use in our shop....looks like its a gas issue....just my 2 cents...

100% argon.. my welder is broken.. its nothing i did wrong..

turbob16hatch · « **Reply #169 on:** March 13, 2010, 01:33:57 AM »

Quote from: jay on March 13, 2010, 01:28:22 AM

Quote from: jundoc on March 12, 2010, 10:15:02 PM
i didnt read all posts...but what kind of gas are you using...should be using argon....thats what we use in our shop....looks like its a gas issue....just my 2 cents...

100% argon.. my welder is broken.. its nothing i did wrong..

I wouldn't go that far.

jay · « **Reply #170 on:** March 13, 2010, 01:37:08 AM »

Quote from: turbob16hatch on March 13, 2010, 01:33:57 AM

Quote from: jay on March 13, 2010, 01:28:22 AM
Quote from: jundoc on March 12, 2010, 10:15:02 PM
i didnt read all posts...but what kind of gas are you using...should be using argon....thats what we use in our shop....looks like its a gas issue....just my 2 cents...

100% argon.. my welder is broken.. its nothing i did wrong..

I wouldn't go that far.

lol im talking about punching monstrous holes in the metal my welder was more like a plasma cutter

jay · « **Reply #171 on:** March 15, 2010, 10:09:56 AM »

well.. welding shop wants 875 to fix the god damn machine...

bigwig · « **Reply #172 on:** March 15, 2010, 10:28:03 AM »

Quote from: jay on March 15, 2010, 10:09:56 AM

well.. welding shop wants 875 to fix the god damn machine...

Call another. $875 is a joke.

malichite · « **Reply #173 on:** March 15, 2010, 10:35:03 AM »

you took it to airgas

jay · « **Reply #174 on:** March 15, 2010, 10:45:58 AM »

Quote from: bigwig on March 15, 2010, 10:28:03 AM

Quote from: jay on March 15, 2010, 10:09:56 AM
well.. welding shop wants 875 to fix the god damn machine...

Call another. $875 is a joke.

well the board alone cost 475... so i guess they are installing the board for 400?

Quote from: malichite on March 15, 2010, 10:35:03 AM

you took it to airgas

friend recommended them

i guess i now need to choose a welder from red d arc.. he says the 100 i paid can be applied towards any red d arc rent to own... they have miller dynasty 200's for about 1700... 12 payments = 150 a month.. not bad.. i can swallow that..
http://www.red-d-arc.com/category_page.aspx?sub_category_id=14

Joseph Davis · « **Reply #175 on:** March 15, 2010, 11:53:31 AM »

$800 welder, $875 to fix, I'll give you -$75 plus shipping.

Honestly, think on a price and LMK.

buk9tp · « **Reply #176 on:** March 15, 2010, 01:12:20 PM »

Why replace a board than can be fixed with a few hours, a multi meter, and some sense? Welder boards are not that complex and at the very least dc amprage And gas control should be able to be salvaged with a hasty runthrough of the welder and possibly bypassing some digital controls. It's a fucking power supply, for christ sakes.

I'll give you -25$ picked up.

Joseph Davis · « **Reply #177 on:** March 15, 2010, 01:16:17 PM »

buk, stop arguing and trying to do business with yourself.

chris · « **Reply #178 on:** March 15, 2010, 05:23:47 PM »

600 dollar new mig welder seems like a great idea.

jay · « **Reply #179 on:** March 15, 2010, 05:28:49 PM »

Quote from: jay on March 15, 2010, 10:45:58 AM

i guess i now need to choose a welder from red d arc.. he says the 100 i paid can be applied towards any red d arc rent to own... they have miller dynasty 200's for about 1700... 12 payments = 150 a month.. not bad.. i can swallow that..
http://www.red-d-arc.com/category_page.aspx?sub_category_id=14

im selling my sc61 turbo kit (for a sad 1200 bucks)

then i figure i can sell the busted welder for 400..

civic i got in the backyard for 1500.. not to mention i got a buyer for my crx for 2700.. i might be able to buy the welder flat out..

if i can atleast manage a nice chunk of change as a downpayment i can put down a decent downpayment... and make my monthly payments less

News:

Author Topic: cummins discussion thread. (Read 136852 times)

chris

chris

bigwig

chris