Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Cooljnateman]

damn chuck looks like your doing work!!! wish my season was as good as yours. BTW have you been hitting them Weights you looking swollen sonnn

YO HE DOES LOOK SWOLL god damn haha thats funny u say that...in person im still the muscel around this kneck da woods!...and that aint tin foil lmfao

[schim187]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

[Cooljnateman]

schim wat can i say yur just a monster

[Towdogg]

Getting it together......   Just installed axles and other front end shit....

Went and bought a new fuel filter at napa..

Shit is gonna be nice...

Still have to do rear disc swap...    I know thats gonna suck!

[Towdogg]

I also found a cheap B16a and a ys1 big spline tranny cheap...  This will be good cause I have the 90-91 ls small spline tranny now...

[Joseph Davis]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

How fucking big are you?

[92CXyD]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

How fucking big are you?

I've done that with a D-series short block, flywheel, clutch and oil pan, no crank pulley or accessories before.

My back hated me for it later.

[schim187]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

How fucking big are you?

Not that big...dad just always made me dead lift wood up onto the back of a flatbed when i lived in AK for firewood...chuck fed me and i moved the engine blocks up and down from the basement to the driveway.

[Towdogg]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

How fucking big are you?

He isn't that big.... lol  More like a country boy that knows how to do shit...  I'd say 5'11"-6' 190-210lbs

And I dont remember the hold engine up with one hand and doing bolts with the other.....  Just the bear hug on that LS and walked up the stairs like it wasn't shit... lol

[Towdogg]

[Joseph Davis]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

How fucking big are you?

He isn't that big.... lol  More like a country boy that knows how to do shit...  I'd say 5'11"-6' 190-210lbs

So he's me with 20-40lbs of muscle on him, gotcha.

I'm going to try some drag racing without my front swaybar.

[Towdogg]

Chris M. Tb and spacer on the golden eagle shit.......   

[drivin96]

few pics i had layin round

[Towdogg]

These nigga's don't know nothing bout that......

Btw.. My eGay cast mani is giving me troubles so im going to try my buddy's OBX topmount....

[Joseph Davis]

The only OBX topmount I had experience with (it may have been generic china, but was thick walled which I associate with OBX) required a T04 on center turbine housing.  It was on an EM1 chassis, and the guy only had a tangental housing + decided to cut into the headlight frame and run no hood to make it work.  Not what I would have done.

Be ready to test fit and take that right off, ED are a much tighter chassis with less clearance. 

FYI, made 422 whp off a B16 with 60-1 on that manifold, sprayed a 100 shot and made 574 with slicks breaking free at 7500 rpms.  Local heart breaker Mustang dyno.  There's nothing wrong with those as far as power production, and the one I'm thinking of didn't have any cracking problems.

[Towdogg]

Ya I dont wanna cut anything on this car....  I'll buy a different mani before that happens... 

Fuck...

[Teg2boo]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

Block + head together? That's impressive 

I did it yesterday with a complete b18a1 block with flywheel, but without the head and it was a fucking pain in the ass. I had to lift it at least 20 times to be able to align it correctly with the bolt hole... Like you, I had to hold it with one hand and the other trying to fit the bolt in the fucking hole.

I'm 6' tall and weight 150lbs btw.

[Towdogg]

He kinda bear hugged it with the head and valve cover....  No fuilds in it with the crank pully in the sky...  No fly wheel i dont  think...

So the OBX topmount fits but like JD said im gonna have to trim the headlight sheet metal...  MAYBE NOT if you guys think it wont hurt my ebay turbo if i cut about half of the intake side off it....

[92CXyD]

nate i swear last time i was there and you came over chuck told you to take that b series up stairs and you said you were to sore from working out...i recall me picking it up and putting it in the car whilst holding the motor with one hand and boltin up the mounts with the other

Block + head together? That's impressive 

I did it yesterday with a complete b18a1 block with flywheel, but without the head and it was a fucking pain in the ass. I had to lift it at least 20 times to be able to align it correctly with the bolt hole... Like you, I had to hold it with one hand and the other trying to fit the bolt in the fucking hole.

I'm 6' tall and weight 150lbs btw.

I did this with my D16.  I had two jack stands to hold the short block close to the height I needed to line up the input shaft to my clutch.

I also used to old head bolts on top of the block to help with controlling the movement of the block when I was setting it in the bay on the jack stands.

[Towdogg]

I said fuck it and trimed behind the headlight abit and cut off some of the turbo now the topmount fits.....   

I'll post pics later cause i got to go to work...

[ApexSilver06MR]

damn chuck...  i want to see some rippers...


i put together like 10 different setups in 2 different cars since your build thread

[Towdogg]

damn chuck...  i want to see some rippers...


i put together like 10 different setups in 2 different cars since your build thread

I know I know....  Shit has been taken awhile.....

[crxvtec91]

damn chuck...  i want to see some rippers...


i put together like 10 different setups in 2 different cars since your build thread

Flip nog you always have a new setup.

[Cooljnateman]

Some pics of the most recent setup taken today, still needs to trim some more spots on the frame and maybe even the compressor housing. Nice tight fit just how she likes it .

[dvst8r]

About that airfilter...

[Cooljnateman]

About that airfilter...

A little screen could work, and also this wont be a DD...so even without one he would be fine....for a little bit haha.

[drivin96]

Chuck in the next day or so ill post up the pics i took

[Towdogg]

I have never ran an air filter on any of the cars I've turboed....  Im not worried...

[Cooljnateman]

I have never ran an air filter on any of the cars I've turboed....  Im not worried...

I didnt run one either for the first couple thousand miles on my first build never had issues but i eventually through one on just to cure one less headache.

[drivin96]