Topic: chop saw question (Read 10209 times)

t_cel_t · « **on:** April 30, 2010, 03:47:45 AM »

how do you guys remove the flash that builds up when using a chop saw from the inside of pipe?
is it my shit ass harbor freight blades?

the only thing i can do now is use my dremel and the little sander drums but that takes forever.(for the inside obviously, outsides i use a bench grinder)
this is what it does

ifly87 · « **Reply #1 on:** April 30, 2010, 04:02:45 AM »

Get rid of the HF blades!! One of those bastards broke in half when I was trying to cut exhaust. I bought a blade for my HF saw from sears and it cut 10x better. Still had some of that shit on the pipe though, I just use an angle grinder or a file to get it off.

narfdanarf · « **Reply #2 on:** April 30, 2010, 09:38:07 AM »

same here I just use a file or die grinder.

weirtech · « **Reply #3 on:** April 30, 2010, 10:57:41 AM »

die grinder with a carbide burr, but on aluminum i use a deburring tool.

dvst8r · « **Reply #4 on:** April 30, 2010, 11:40:35 AM »

Outside gets the belt sander, inside gets the die grinder.

theidealone · « **Reply #5 on:** April 30, 2010, 12:59:01 PM »

Die grinder with a carbide bit for both in and out.

turbob16hatch · « **Reply #6 on:** April 30, 2010, 01:27:57 PM »

I use a belt sander and fsurface the tube to it's flat/square and then use a deburing tool on the inside. 4" flap disk on the outside. takes 2 sec.

ryan89crx · « **Reply #7 on:** April 30, 2010, 01:28:31 PM »

Bastard file, then a bench grinder

danz · « **Reply #8 on:** April 30, 2010, 06:42:12 PM »

round file for the win

sfa22r · « **Reply #9 on:** May 01, 2010, 02:23:43 AM »

tin snips/side cutting pliers

dvst8r · « **Reply #10 on:** May 01, 2010, 10:43:20 AM »

My latest technique is just using the dry cut saw instead of the chop saw.

snm95ls · « **Reply #11 on:** May 01, 2010, 11:10:01 AM »

Substitute said chop saw AKA hot saw for a bandsaw or a cold saw.

Die grinder on the inside and 4" high speed air sander equipped with a flapwheel on the outside.

ApexSilver06MR · « **Reply #12 on:** May 01, 2010, 01:01:40 PM »

+1 on the round file!

turbob16hatch · « **Reply #13 on:** May 01, 2010, 01:09:02 PM »

Who has time to use a file on this shit?

mrgreengenes · « **Reply #14 on:** May 05, 2010, 01:56:45 AM »

t_cel_t · « **Reply #15 on:** May 05, 2010, 02:41:51 AM »

Quote from: mrgreengenes on May 05, 2010, 01:56:45 AM

MIG

we are not talking about welders

ifly87 · « **Reply #16 on:** May 05, 2010, 03:29:10 AM »

Quote from: turbob16hatch on May 01, 2010, 01:09:02 PM

Who has time to use a file on this shit?

If you have a decent file thats not all beat to shit, and put a little man behind it that flashing is gone in seconds. You dont actually file all of the flashing down, just hit the edge of the pipe at an angle and it cuts the flashing right off.

HiProfile · « **Reply #17 on:** May 05, 2010, 09:05:03 AM »

If it's super-thick from say sch40 pipe, I use a pliers to get most of it off. Then I go at it with a bench grinder.

jay · « **Reply #18 on:** May 08, 2010, 02:07:41 AM »

buy a band saw! world of a difference!

i found myself using a butter knife that i flattend out the entire blade on the bench grinder.. to make it more ridged.. kinda like a nigger rigged deburring tool.. works great at getting the annoying stuff out quickly.. if there are stubborn parts i whoop out the rounded filers.. but ever since i switched to a band saw i havent had to do that shit since

caged · « **Reply #19 on:** May 08, 2010, 03:56:21 AM »

I use a die grider too, it would have to be one of my most used tools

News:

Author Topic: chop saw question (Read 10209 times)

sfa22r