Topic: Jearbear's Dirty D (Read 19512 times)

ochoa · « **on:** April 01, 2009, 02:02:09 AM »

I have been collecting parts for some time now, finally got the build underway

heres the set up

1988 CRX Si

Engine
D16 ZC
Aries Pistons
Eagle Rods
ACL Bearings
ARP headstuds
Fj Gasket kit
Y8 Head
LSD Clutch Kit (rated for 385 ft lbs)

Turbo setup
Welded Egay manifold
Wrx turbo
Egay intercooler
DSM 450's
Greddy BOV
Walbro 255
LM1 wideband w/ autometer gauge
EDT traction bar kit

Goal- max out turbo and injectors then upgrade later this summer when i have more funds

all the machine work is being done by my friend at his work

Before

After

Caleb at work

and now

and some milf action FTW

widebody93 · « **Reply #1 on:** April 01, 2009, 02:08:44 AM »

pictures of the car too

ochoa · « **Reply #2 on:** April 01, 2009, 02:35:29 AM »

ill get some up on friday when i go back home and have some time to work on the car

brine04 · « **Reply #3 on:** April 01, 2009, 03:20:04 AM »

Quote from: ochoa on April 01, 2009, 02:35:29 AM

ill get some up on friday when i go back home and have some time to work on the car

Fucking rights you will. Buy a bigger turbo too

widebody93 · « **Reply #4 on:** April 01, 2009, 04:02:01 AM »

something like a 62mm slug

mycarslow · « **Reply #5 on:** April 01, 2009, 12:32:49 PM »

bout time you do this boy :somb:

Towdogg · « **Reply #6 on:** April 01, 2009, 12:52:50 PM »

Pics of car??

Now!

mycarslow · « **Reply #7 on:** April 01, 2009, 02:05:33 PM »

just a crx

Towdogg · « **Reply #8 on:** April 01, 2009, 02:15:02 PM »

I have those wheels also....

They are light wheels. Mine are gloss black.

ochoa · « **Reply #9 on:** April 01, 2009, 06:40:48 PM »

bad news from the machine shop, after block was honed the pistons were under spec so they need to be sent out to be coated and the pins need to be upgraded to handle more boost.... so new plans ....all out race car now i need to get a big turbo. The car is going to be painted olive drab i also have some 16'' black rota slip knockoffs im gunna rock

Towdogg · « **Reply #10 on:** April 01, 2009, 06:52:40 PM »

That sucks.....

ryan89crx · « **Reply #11 on:** April 01, 2009, 07:23:20 PM »

sounds like you need a better machine shop

widebody93 · « **Reply #12 on:** April 01, 2009, 08:36:27 PM »

They didnt mic out the pistons before they bored it. WTF. I would have them get you a new block or sleeve it for free

Conceptz-X · « **Reply #13 on:** April 01, 2009, 09:19:00 PM »

Quote from: widebody93 on April 01, 2009, 08:36:27 PM

They didnt mic out the pistons before they bored it. WTF. I would have them get you a new block or sleeve it for free

+1

bb4caleb · « **Reply #14 on:** April 01, 2009, 09:41:49 PM »

Quote from: widebody93 on April 01, 2009, 08:36:27 PM

They didnt mic out the pistons before they bored it. WTF. I would have them get you a new block or sleeve it for free

the pistons were suppossed to be .020 over which would have been all fine and dandy but... before honing the block i checked the pistons and they are only .002 over stock bore.

and all the cylinders were tappered .002 and one cyl was out of round about .0025. no good. but the only other d block we have arould is a z6 that had been laying in the rain and basically junk. so we honed it to see what we could do and it turned out that they cleaned up ..0055 over what the pistons are....but the pistons recamended ptw is .004 so we are going to send the pistons out for coating and gain .001 so we should only be .0005 over spec. but for engines running high boost ( 30 psi +++) the piston manufacturers usually say to have a little more clearance. so the pistons will be sent out to coat asap and we'll see where that gets us. Have any of you had any problems with the wrist pins breaking???

crxvtec91 · « **Reply #15 on:** April 01, 2009, 10:04:57 PM »

How much does it cost to get them coated.

Conceptz-X · « **Reply #16 on:** April 01, 2009, 10:08:51 PM »

Thats alot of fucking coating if your trying to build the piston up.

I'd be chewin on someone's ear, machine shop, piston salesman, etc.

bb4caleb · « **Reply #17 on:** April 01, 2009, 10:16:50 PM »

cost is 16 per piston. and i think your getting the wrong idea on the coating. we are only looking for .001. its pretty common to do. and its not the machine shops fault. we went into it knowing that it was going to be out of spec. but we cant return the pistons so we are just doing what we can do.

bb4caleb · « **Reply #18 on:** April 01, 2009, 10:26:49 PM »

coating also helps when upper cyl lubrication is weak and helps avoid scratching. so its a win win situation. but it will set us back a little.. o well gives me some time to work on my setup ; :yes:

mycarslow · « **Reply #19 on:** April 02, 2009, 01:15:06 AM »

dont like like ill be able to work on mine for some time... im might be losing my DL dang but i might be able to get on Illinois court supervision for speeding tickets

i hope

ochoa ima have to run the rex when my shit box runs so give me till 2020 haha it might run then

ochoa · « **Reply #20 on:** April 02, 2009, 02:18:25 AM »

sorry i kinda or made that sound bad. when i bought the pistons the were susposed to be .20 over but the order was over the phone so they wont take them back now. so caleb is doing what he can to make them work give him a break his mom is hotter than shit

heres some more pics of the slut as it sits now in black primer

HiProfile · « **Reply #21 on:** April 02, 2009, 02:24:39 AM »

Quote from: ochoa on April 01, 2009, 02:02:09 AM

and some milf action FTW

I couldn't tell if these were older looking young chicks or younger looking old chicks. Nice :yes: The cool thing about older chicks getting plastic sugurey - they do it right. No lopsided boobs, visible scars - just awsomeness.

mycarslow · « **Reply #22 on:** April 05, 2009, 08:57:53 PM »

ne news on the car :somb:

biscuit · « **Reply #23 on:** April 05, 2009, 09:27:53 PM »

Are you using the manifold that i sold you Ochoa?

mycarslow · « **Reply #24 on:** April 05, 2009, 10:14:04 PM »

pretty sure he is

danz · « **Reply #25 on:** April 05, 2009, 10:51:53 PM »

id moff those miffs.

bb4caleb · « **Reply #26 on:** April 05, 2009, 11:15:39 PM »

he needs a bigger turbine. mycarslow?

!!!!! your never gonna get yours done so hook him up son

mycarslow · « **Reply #27 on:** April 05, 2009, 11:22:38 PM »

boy i just called you you lil fucker i was going ask you to look @ some piston and let me know what you think

widebody93 · « **Reply #28 on:** April 05, 2009, 11:25:05 PM »

Any of you 3 have a boosted car runing yet?

mycarslow · « **Reply #29 on:** April 05, 2009, 11:34:52 PM »

widebody all 3 of us are still in school ... i for one am just having for fucking around and saving for 375 to 400hp sohc non vtec ..... mine was running till a nasty boost spike

News:

Author Topic: Jearbear's Dirty D (Read 19512 times)