Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[walter]

what title says, im looking for one piston ring grinder for good prices but shipiping to Europe are crazy (ive find even the shipping cost for pistons!) so i was wondering if someone make a realhomemade piston ring grinder for gap rings.

another question is what gap i should give to new piston rings to my new setup (vitara/eagle on Z6) i'd use it for drag and road racing.

any help?

Thanks

[92CXyD]

I just use a little file for like $1.00usd   :yes:

Its easy on most honda ring. Usually I only have to file a little just make sure you file in both directions and in small increments at a time.

[highroller54]

any help?

Walter I have what you need but I have a problem, I asked you for some help with getting a vti tach or whole cluster. You told me to basically fuck off because you couldn't be bothered. well guess what princess.

[Towdogg]

any help?

Walter I have what you need but I have a problem, I asked you for some help with getting a vti tach or whole cluster. You told me to basically fuck off because you couldn't be bothered. well guess what princess.

One hand washes the other.... But not this time....   

[92CXyD]

what title says, im looking for one piston ring grinder for good prices but shipiping to Europe are crazy (ive find even the shipping cost for pistons!) so i was wondering if someone make a realhomemade piston ring grinder for gap rings.

another question is what gap i should give to new piston rings to my new setup (vitara/eagle on Z6) i'd use it for drag and road racing.

any help?

Thanks

If my memory serve me right I have 0.018 top and 0.020 second. For my 0.5mm o/s vitaras.  ;D

[highroller54]

any help?

Walter I have what you need but I have a problem, I asked you for some help with getting a vti tach or whole cluster. You told me to basically fuck off because you couldn't be bothered. well guess what princess.

One hand washes the other.... But not this time....   

I believe Chris M had the same problem with mr Euro to.

[ryan89crx]

File in a vice and do it by hand

[walter]

any help?

Walter I have what you need but I have a problem, I asked you for some help with getting a vti tach or whole cluster. You told me to basically fuck off because you couldn't be bothered. well guess what princess.

what? where? i can try to find one for you but it's expensive.  i even sold vti tach of my crashed VTI to a american guy.

thanks for "help".

[crxvtec91]

what title says, im looking for one piston ring grinder for good prices but shipiping to Europe are crazy (ive find even the shipping cost for pistons!) so i was wondering if someone make a realhomemade piston ring grinder for gap rings.

another question is what gap i should give to new piston rings to my new setup (vitara/eagle on Z6) i'd use it for drag and road racing.

any help?

Thanks

If my memory serve me right I have 0.018 top and 0.020 second. For my 0.5mm o/s vitaras.  ;D

Shit I have the same, motor is about to run in the next few days. Walter cheap file and do it by hand, not to much at a time!!!

[keelay]

any help?

Walter I have what you need but I have a problem, I asked you for some help with getting a vti tach or whole cluster. You told me to basically fuck off because you couldn't be bothered. well guess what princess.

Be the bigger man, and also help a RHMT brother. Kindness comes back to you man.

[d112crzy]

A dremel works just fine.

[HiProfile]

Just make sure to deburr all 4 edges, to file it straight, and don't chip the ring edges. You could take a larger c-channel or 2 angle iron chunks, drill holes in them, weld them to a plate, and insert a arbor adapter for a thin grinding disc. Since it's such a small job, it's really not worth it. Instead I spent $25 on a Summit piece of junk that got the job done cleanly & quickly. Looks like they aren't so cheap now, so I'd suggest using a small needle file.