Topic: what size oil restrictors are you guys running? (Read 7920 times)

Zeniceguycrx · « **on:** May 12, 2009, 10:58:24 PM »

well what ya got going on

1slow91hf · « **Reply #1 on:** May 12, 2009, 11:36:49 PM »

stevemode line model

or .065" jb weld and drill bit edition

turbob16hatch · « **Reply #2 on:** May 13, 2009, 02:56:10 AM »

i just weld the fitting shut and drill a 1/16" hole

bigdaddyvtec · « **Reply #3 on:** May 13, 2009, 05:08:56 AM »

.035 on the DBB CRHA

bigdaddyvtec · « **Reply #4 on:** May 13, 2009, 07:07:10 AM »

what turbo??? -4 is too big. -3 is cool for a journal bearing turbo, They reccomend a .065 to .100 for journal bearings...

I actrually talked to a garett engineer and he told me .035 is fine for BB CRHAs.

Zeniceguycrx · « **Reply #5 on:** May 13, 2009, 06:25:20 PM »

t3 48/60

sloTeg · « **Reply #6 on:** May 13, 2009, 08:21:54 PM »

does anybody run restrictors in their Holsets?

1slow91hf · « **Reply #7 on:** May 14, 2009, 12:59:54 AM »

the sizes given are pretty much flat rate across the turbo world so some may some may not run them
never hurts to have a bit of restriction

ratcityrex · « **Reply #8 on:** May 14, 2009, 01:34:30 AM »

Ive always used -3 lines and .065 restrictor on everything ive cared about. Everything else got the good old 3/8" fuel line with a 1/8" mnpt cap shoved inside it with a 1/8" hole drilled in it. And yes I would run a restrictor on a holset. I dont know about you but at 7500 im pushing close to 85psi of oil pressure.

onlyflash944 · « **Reply #9 on:** May 14, 2009, 05:19:53 PM »

what ever size the inside of a aluminum pop rivet is. on a 14b with no problems

Urban Indian · « **Reply #10 on:** May 15, 2009, 02:22:38 AM »

Quote from: sloTeg on May 13, 2009, 08:21:54 PM

does anybody run restrictors in their Holsets?

ever looked at the thing they come off?

do you see restrictors? no way. just rock it

BoostForLife · « **Reply #11 on:** May 15, 2009, 02:26:47 AM »

Im running a -3an to 1/8npt fitting, then 1/8 to 1/4npt converter, into 1/4 by 12X1.5 fitting on the holset.
I don't think it needs a restrictor, this is on a HX35.

Atticus · « **Reply #12 on:** May 15, 2009, 03:29:05 AM »

adjustable FTW

glustic · « **Reply #13 on:** May 19, 2009, 04:50:41 PM »

-3 an feed line, .065" restrictor

to4e turbo 50 trim

speedjunky01 · « **Reply #14 on:** May 19, 2009, 11:29:33 PM »

dont run the function 3 restrictor

the one i got is -4an, then had to 90* it then convert -4 to -3

end result:

hope i can make it stop pissing oil

JB weld restrictor FTW

ifly87 · « **Reply #15 on:** May 20, 2009, 01:26:13 AM »

JBweld restrictor ftl, I've chowed a turbo because the jbweld inside the fitting came loose and plugged up the hole. Now I tap threads into a fitting, thread a set screw into it with red locktite, and drill a .060 hole in the setscrew.

Lowerit · « **Reply #16 on:** May 20, 2009, 10:00:15 AM »

Take a riviet, remove the shaft and drop it in the line.

Blammo.. Oil restrictor.

Also seen guys use washers from rivets...no issue

onlyflash944 · « **Reply #17 on:** May 20, 2009, 10:41:38 AM »

Quote from: Lowerit on May 20, 2009, 10:00:15 AM

Take a riviet, remove the shaft and drop it in the line.

Blammo.. Oil restrictor.

Also seen guys use washers from rivets...no issue

worked for me, just make sure to use a rivet out of whatever material your fittings are

SirDragsAlot · « **Reply #18 on:** May 20, 2009, 11:00:01 PM »

i bought a 1/4 npt needle valve meant for hydraulic applications, simply adjust to your needs. perhaps i will use some kind of pressure gauge to tune the oil flow when my project is ready

danz · « **Reply #19 on:** May 21, 2009, 02:39:14 AM »

fill fitting with weld, drill with push drill and small drill bit.

done.

another win for the welder

News:

Author Topic: what size oil restrictors are you guys running? (Read 7920 times)

BoostForLife