Topic: hatchbones ride (Read 8458 times)

hatchbone · « **on:** December 08, 2011, 11:37:43 PM »

last one got the delete when site went down so i just copied some pics for this so fuck you

Hatchbone Dyno Session HD

Hatchbone finally runs 10s

robus · « **Reply #1 on:** December 09, 2011, 04:25:38 AM »

Pretty hardcore

NoPistons! · « **Reply #2 on:** December 09, 2011, 07:16:08 AM »

Dont tell anyone but i'm saving that gas station pic as wallpaper.

You drive that thing on the street?! Hell yeah.

bigdaddyvtec · « **Reply #3 on:** December 09, 2011, 03:32:05 PM »

Boat anchor love my niggle

SloS13 · « **Reply #4 on:** December 09, 2011, 08:32:07 PM »

hot damn. Is that a civic with a turbo?

hatchbone · « **Reply #5 on:** December 09, 2011, 09:38:09 PM »

Quote from: SloS13 on December 09, 2011, 08:32:07 PM

hot damn. Is that a civic with a turbo?

its a turbo with a civic

hatchbone · « **Reply #6 on:** December 09, 2011, 09:39:13 PM »

got some new goods for my vac setup

hatchbone · « **Reply #7 on:** December 11, 2011, 04:11:57 AM »

Quote from: bigdaddyvtec on December 09, 2011, 03:32:05 PM

Boat anchor love my niggle

what turbo you end up going with?

DSharp · « **Reply #8 on:** December 24, 2011, 12:32:13 AM »

your diff looks like mine! still works though...

hatchbone · « **Reply #9 on:** December 24, 2011, 03:25:06 PM »

I got new washers and re assembled it as is and works like a champ

theidealone · « **Reply #10 on:** December 24, 2011, 04:30:12 PM »

I didnt have the same ones, but I had quick release with that plastic shit, and it melted where it came out of the turbo. Worked great for my BOV, and stuff like that. Someone told me they make all metal quick release adapters.

DSharp · « **Reply #11 on:** December 24, 2011, 09:43:06 PM »

Quote from: hatchbone on December 24, 2011, 03:25:06 PM

I got new washers and re assembled it as is and works like a champ

yep. same here. obx washers are like potato chips.

jarebear667 · « **Reply #12 on:** December 25, 2011, 12:28:30 AM »

What'd you end up for power?

hatchbone · « **Reply #13 on:** December 25, 2011, 03:08:00 AM »

Around 800-820 it kept spinning over 8k on the dyno but it made 702 on 24psi its now at 34psi the dyno I use has a new strap design I just haven't put it back on the rollers,first thing next year though

crxvtec91 · « **Reply #14 on:** December 25, 2011, 12:27:33 PM »

Fucking baller, will the obx hold up?

hatchbone · « **Reply #15 on:** December 25, 2011, 03:31:31 PM »

Has for three seasons already lol

crxvtec91 · « **Reply #16 on:** December 25, 2011, 08:59:00 PM »

Quote from: hatchbone on December 25, 2011, 03:31:31 PM

Has for three seasons already lol

Damn I seen a lot of trash obx around here under 600hp

hatchbone · « **Reply #17 on:** December 27, 2011, 03:22:38 AM »

Quote from: crxvtec91 on December 25, 2011, 08:59:00 PM

Quote from: hatchbone on December 25, 2011, 03:31:31 PM
Has for three seasons already lol

Damn I seen a lot of trash obx around here under 600hp

get the washer kit and re torque and you good to go for half price

flat_black · « **Reply #18 on:** December 31, 2011, 12:31:47 AM »

brian is still using an OBX in his trans, thats about the only thing that hasnt broke...

I used one for 3 years or so from 500-600whp without issue, i did break the washers but upgraded and seemed fine after that

hatchback · « **Reply #19 on:** January 03, 2012, 12:39:21 AM »

Wheres the porn? You fail.

hatchbone · « **Reply #20 on:** January 03, 2012, 01:26:00 AM »

Your first post was coming at me asking me where the porn be ,I think I should be asking you that

bigdaddyvtec · « **Reply #21 on:** January 04, 2012, 10:21:33 PM »

Quote from: hatchbone on January 03, 2012, 01:26:00 AM

Your first post was coming at me asking me where the porn be ,I think I should be asking you that

if people ar breaking obx diffs theyre nos tetting them up right. I beat mine harder than I beat weidebodys ex roast beef and never an iddue, Washers are a nust.

hatchbone · « **Reply #22 on:** January 10, 2012, 09:02:01 PM »

should not be a issue if set up properly

hatchbone · « **Reply #23 on:** February 19, 2012, 02:32:33 PM »

so got around to pulling my head off this is what it looks like when your springs try and pull the valves through backwards not a big deal, could of been a lot worse, could of snapped off here are some pics never will i run superstretch again. couldn't handle the anti lag

HiProfile · « **Reply #24 on:** February 19, 2012, 02:57:56 PM »

I'm not understanding what happened, besides the valve beating the piston. Mind explaining, such as failed retainers, keepers, or valve stems?

hatchbone · « **Reply #25 on:** February 19, 2012, 03:05:27 PM »

the valves got so hot from my anti lag they got soft and the force of the spring wanted to pull them out backwards, the pistons are fine but a couple of the retainers are a little beat from hitting the rockers when the valve stretched

HiProfile · « **Reply #26 on:** February 19, 2012, 03:10:09 PM »

Time to add sodium...at least for the exhaust side. The only problem is honda valve stems are already so thin.

bigdaddyvtec · « **Reply #27 on:** February 19, 2012, 05:09:10 PM »

Quote from: HiProfile on February 19, 2012, 03:10:09 PM

Time to add sodium...at least for the exhaust side. The only problem is honda valve stems are already so thin.

No need for sodium valves. At all.

Jake I dont think it weas the antilag. Looks like it went lean (you did mention this happened after upping the boost?) It went lean and EGTs got very very hot by the looks of it, maybe more than once... Fuck Superstretch/snap valves though. Go Ferrea. Ive NEVER had an issue. Valves do look like contact was made... Pics of valve reliefs?

NICE CATCH Jake....Glad those things didnt cost you a bottom end

hatchbone · « **Reply #28 on:** February 19, 2012, 06:10:51 PM »

I'll get some more pics up soon could of leaned I do have my data logs from my last race ill peep and see what they say

hatchbone · « **Reply #29 on:** March 28, 2012, 10:42:21 PM »

head is back new valves and seals should be rollin by end of weekend

News:

Author Topic: hatchbones ride (Read 8458 times)