Topic: Went 10.608 @ 132.19 today. (Read 13469 times)

Dr. D-Series · « **on:** April 19, 2009, 09:17:59 PM »

Hot. Its nice to back up my past runs. 4 10 second passes so far this year. Im ALMOST satisfied.

The bad news....

Coming out of the burnout box @ 8900 in 2nd gear the differential exploded.
So I only got one run in today, but at least it was decent.

Went soft on the car 1st run, lift throttle shifting @ roughly 83-8400 rpm every gear. (8900 normally)

I regret that now, should have went balls out and possibly brought home a 10.4x

BTW im glad that the car didnt lose any mph after adding the cage (75% done, 2 front posts and floor plates left to weld in).

Hot.

chris · « **Reply #1 on:** April 19, 2009, 09:25:36 PM »

Going welded diff? Sent that spacer out this weekend. Im impressed as always.

Dr. D-Series · « **Reply #2 on:** April 19, 2009, 09:30:37 PM »

Might go obx. I feel welded diff is too dangerous with stock axles. The wall hurts.

1991civicsi · « **Reply #3 on:** April 19, 2009, 09:37:26 PM »

Any problems towing the car back with the damaged trans?

Dr. D-Series · « **Reply #4 on:** April 19, 2009, 09:45:07 PM »

Nope.

crttaz · « **Reply #5 on:** April 19, 2009, 10:02:04 PM »

Quote from: Dr. D-Series on April 19, 2009, 09:30:37 PM

Might go obx. I feel welded diff is too dangerous with stock axles. The wall hurts.

Got one local to me. He was a member on OHMT

dvst8r · « **Reply #6 on:** April 19, 2009, 10:18:27 PM »

How was the boost today? Solid now, or still dropping off?

Urban Indian · « **Reply #7 on:** April 19, 2009, 10:18:41 PM »

excellent, I admire you

but still

no vids = fail

hotrex · « **Reply #8 on:** April 19, 2009, 10:40:31 PM »

noone cares.

Joseph Davis · « **Reply #9 on:** April 19, 2009, 10:48:53 PM »

An OBX LSD may destabilize you, if you aren't careful. Closely inspect the washers (where the diff pin used to be) and make sure they are arraigned so that they are a little tight when you close the diff up. If you leave them out, or jingling, you may get that sweet unstable side-to-side under power phenomenon. Makes it really hard to hold the car between the lanes.

BangBusMaster · « **Reply #10 on:** April 19, 2009, 10:50:08 PM »

Awsome time dude

I'd be fucking stoked to run those times on that build.

crxvtec91 · « **Reply #11 on:** April 19, 2009, 10:58:51 PM »

Joe nice times as always! I have that obx for you, not 100% you will be able to use it but its yours.

hotrex · « **Reply #12 on:** April 19, 2009, 11:00:03 PM »

Quote from: c0mpl3x on April 19, 2009, 10:42:30 PM

Quote from: hotrex on April 19, 2009, 10:40:31 PM
noone cares.

you managed 0-911 in 12.1 seconds of fire

u cant even afford to do that

88dx · « **Reply #13 on:** April 20, 2009, 12:03:50 AM »

Nice times on the setup. :yes:

d-rail · « **Reply #14 on:** April 20, 2009, 01:33:25 AM »

Quote from: hotrex on April 19, 2009, 11:00:03 PM

Quote from: c0mpl3x on April 19, 2009, 10:42:30 PM
Quote from: hotrex on April 19, 2009, 10:40:31 PM
noone cares.

you managed 0-911 in 12.1 seconds of fire

u cant even afford to do that

Nobody has to be able to afford to do it. All anyone has to do is drive to your house and let you work on something.

d-rail · « **Reply #15 on:** April 20, 2009, 01:36:20 AM »

But on topic good job with the setup man and I can only dream of having as good of a time as you with like 10x the money in mine. Good luck and after I blow my motor to hell and back I'll be looking at you and your progress.

onlyflash944 · « **Reply #16 on:** April 20, 2009, 02:19:18 AM »

check your pm

and good work on the diff. i blew one last year with a stock z6. they're not the most robust part in the case

any videos?

caged · « **Reply #17 on:** April 20, 2009, 02:44:58 AM »

Good shit!!

chris · « **Reply #18 on:** April 20, 2009, 03:05:05 AM »

Quote from: c0mpl3x on April 19, 2009, 10:23:20 PM

i bet you could get rhmt to sponsor you, in some way/form

I just sent him free parts so its already begun

BoostForLife · « **Reply #19 on:** April 20, 2009, 03:16:12 AM »

Quote from: chris M on April 20, 2009, 03:05:05 AM

Quote from: c0mpl3x on April 19, 2009, 10:23:20 PM
i bet you could get rhmt to sponsor you, in some way/form

I just sent him free parts so its already begun

I was about to say that Chris is already kind of doing it.

crttaz · « **Reply #20 on:** April 20, 2009, 03:23:42 AM »

Quote from: Joseph Davis on April 19, 2009, 10:48:53 PM

An OBX LSD may destabilize you, if you aren't careful. Closely inspect the washers (where the diff pin used to be) and make sure they are arraigned so that they are a little tight when you close the diff up. If you leave them out, or jingling, you may get that sweet unstable side-to-side under power phenomenon. Makes it really hard to hold the car between the lanes.

JD, no complaints here on all my installs, the washers are to control noise, not preload.

Dr. D-Series · « **Reply #21 on:** April 20, 2009, 09:23:08 AM »

Anyone know which cable trans have small and large bearings ?

Obx only makes the lsd for 40mm bearings correct ?

BTW thanks guys.

birdley42008 · « **Reply #22 on:** April 20, 2009, 09:26:14 AM »

What is your 60 foot?

Dr. D-Series · « **Reply #23 on:** April 20, 2009, 09:30:57 AM »

It went 1.69

Not my best but not bad.

Joseph Davis · « **Reply #24 on:** April 20, 2009, 09:31:03 AM »

Chuck, have two at the shop that fight you under power, where before they were stable peg leggers.

turbob16hatch · « **Reply #25 on:** April 20, 2009, 09:39:43 AM »

i thought it was pretty well known that civic's torque steer, mainly d series.

Joseph Davis · « **Reply #26 on:** April 20, 2009, 09:44:37 AM »

They don't when there's an intermediate shaft and an alignment involved. Neither of these cars are D-series.

birdley42008 · « **Reply #27 on:** April 20, 2009, 12:43:52 PM »

What gear do you preload in? Atleast 2nd or 3rd correct.

onlyflash944 · « **Reply #28 on:** April 20, 2009, 12:48:29 PM »

Quote from: Dr. D-Series on April 20, 2009, 09:23:08 AM

Anyone know which cable trans have small and large bearings ?

Obx only makes the lsd for 40mm bearings correct ?

yep, but if you got the dough, quaffie makes the 35mm ones. you should be able to find five 40mm trannys for the price of one quaffie 35mm diff

http://www.importdpsonline.com/Store/Product/ItmGroupDetail.aspx?GroupId=55998&Make=HONDA

might have to cross refrence the engine code to the tranny code but hope it helps

fysh · « **Reply #29 on:** April 20, 2009, 12:56:29 PM »

News:

Author Topic: Went 10.608 @ 132.19 today. (Read 13469 times)

chris

chris

BoostForLife

birdley42008

birdley42008