Topic: GSR trans case has a small crack (Read 6450 times)

jdmshocker · « **on:** August 01, 2009, 06:49:07 PM »

so i'm putting my hydro gsr tranny back together and i have a slight crack on the case, ill post a pic

Shitty camera phone pics

jdmshocker · « **Reply #1 on:** August 01, 2009, 06:52:12 PM »

how do i go about fixing it?

onlyflash944 · « **Reply #2 on:** August 01, 2009, 07:46:20 PM »

option a: weld it proper

option b: jb weld it proper

jdmshocker · « **Reply #3 on:** August 01, 2009, 07:52:21 PM »

i was probably going to JB weld, i was actually thinking about using Quicksteel, me and my dad have used it on our boat engine (chevy 350) and the exhaust manifolds. I figure the crack is very small and filling it with JB weld or something like that would be just fine?

Ntrain2k · « **Reply #4 on:** August 01, 2009, 08:56:02 PM »

It depends on where the crack is, how big it is, etc.

Quote from: jdmshocker on August 01, 2009, 06:49:07 PM

so i'm putting my hydro gsr tranny back together and i have a slight crack on the case, ill post a pic

Got that pic yet?

jdmshocker · « **Reply #5 on:** August 02, 2009, 01:18:25 AM »

PICS

widebody93 · « **Reply #6 on:** August 02, 2009, 04:20:18 AM »

I suggest taking it to a machine shop after you have it hot tanked. let then groove into it with a die grinder and re tig it from the outside. NOT FROM THE INSIDE

Ntrain2k · « **Reply #7 on:** August 02, 2009, 01:38:44 PM »

That shit needs to be welded at a minimum.

I'd probably hunt for a new case or tranny myself.

jdmshocker · « **Reply #8 on:** August 02, 2009, 01:57:40 PM »

damn, i just sanded it some and put on some quicksteel stuff, i guess i'll start looking for a new case

civiceggturbo · « **Reply #9 on:** August 02, 2009, 02:22:48 PM »

grind that shit off and buy someone a 30 to weld it

onlyflash944 · « **Reply #10 on:** August 02, 2009, 02:28:38 PM »

Quote from: civiceggturbo on August 02, 2009, 02:22:48 PM

grind that shit off and buy someone a 30 to weld it

jdmshocker · « **Reply #11 on:** August 02, 2009, 02:29:35 PM »

thanks! i have a buddy with a tig welder hopefully he can weld it up for me!

chris · « **Reply #12 on:** August 02, 2009, 02:33:07 PM »

cast is very tough to weld correctly

onlyflash944 · « **Reply #13 on:** August 02, 2009, 02:37:10 PM »

Quote from: chris M on August 02, 2009, 02:33:07 PM

cast is very tough to weld correctly

yes, make sure he knows whats going on

jdmshocker · « **Reply #14 on:** August 02, 2009, 02:39:18 PM »

any advice or tips for tig welding the case?

chris · « **Reply #15 on:** August 02, 2009, 03:06:18 PM »

aluminum sweats out oil if oil has been present. Most welders cant do cast correctly.

jdmshocker · « **Reply #16 on:** August 02, 2009, 03:18:52 PM »

so really i need to bring it to a really good welder or get another case.................damn i'm shit out of luck

onlyflash944 · « **Reply #17 on:** August 02, 2009, 06:32:43 PM »

Quote from: jdmshocker on August 02, 2009, 03:18:52 PM

so really i need to bring it to a really good welder or get another case.................damn i'm shit out of luck

yes

Ghetto_D · « **Reply #18 on:** August 02, 2009, 07:23:54 PM »

Just go to the junkyard and get a new case and be done with it.

jdmshocker · « **Reply #19 on:** August 02, 2009, 11:30:33 PM »

yeah, problem is there is no integra's at all in the junkyards around me :/ I'll have to source out a new case online

89shithatch · « **Reply #20 on:** August 03, 2009, 12:47:35 AM »

jb weld it and run that fucker.

t_cel_t · « **Reply #21 on:** August 03, 2009, 05:03:13 AM »

hit the crack with a torch for a few mins that should burn off most of the oil, then rinse with acetone/alcohol/brake cleaner something that cuts oil.

d-rail · « **Reply #22 on:** August 03, 2009, 05:42:17 AM »

If you heat if up and clean it a few cycles then weld it while its hot you should be ok. But putting filler in somewhere that has already cracked do to stress is not the answer.

jdmshocker · « **Reply #23 on:** August 03, 2009, 10:22:24 AM »

yeah brake cleaned the hell out out of it, but i didn't try torch it or burning off the oil, good idea. I'll probably try to get a dremel or something on it as well before welding it

Ravage70 · « **Reply #24 on:** August 04, 2009, 12:53:00 AM »

is that the outer case?
I have one for sale 50 shipped

crttaz · « **Reply #25 on:** August 04, 2009, 02:41:50 AM »

Quote from: Ravage70 on August 04, 2009, 12:53:00 AM

is that the outer case?
I have one for sale 50 shipped

a fucking steal!

jdmshocker · « **Reply #26 on:** August 04, 2009, 02:56:54 AM »

Quote from: Ravage70 on August 04, 2009, 12:53:00 AM

is that the outer case?
I have one for sale 50 shipped

I'll keep you in mind, may have found two trans locally.

bigdaddyvtec · « **Reply #27 on:** August 04, 2009, 03:18:36 AM »

grind along the crack SLIGHTLY, hit with torch SLIGHTLY, drill 2 small holes at either end of the crack and tig it. Tranny cases are tricky ask me how I know....

stealthiskey · « **Reply #28 on:** August 04, 2009, 08:42:13 AM »

Quote from: bigdaddyvtec on August 04, 2009, 03:18:36 AM

drill 2 small holes at either end of the crack

+1111!!1

ifly87 · « **Reply #29 on:** August 04, 2009, 02:38:40 PM »

Yeah be carefull if you torch it, heat can change the properties of the aluminum pretty easily. Damn. I wouldnt jb weld it, i'll bet that thing opens up when there's a heavy load on it. I'm supprised it didnt come apart.

News:

Author Topic: GSR trans case has a small crack (Read 6450 times)

civiceggturbo

chris

chris