:::RHMT::: Real Home Made Turbo
General Category => Forced Induction => Topic started by: lsone_chevelle on March 22, 2009, 10:45:52 PM
-
Well guys... Figured I shall post up some current pics of the car and where it is sitting. I'll let the pics do the speaky speaky.
**build thread from previous site that failed**
Start out as a bone stock 72 Chevelle malibu from my grandfather(he bought it brand new). 4 wheel drums, 350, turbo 350 tranny, 10 bolt, power nothing, 1 speaker am radio.
I first put true duals on it, rebuilt the heads, cleaned them up, slapped a cam, LT headers, and some carb adjustments and ran it for a year. Also had S10 ZQ8 wheels on it(the 5 spoke style)
I then installed the following within the next 3 years(all major suspension was done winter of 06). I put some on in the winter, drove it a summer, took it apart that winter, and drove it a summer, etc.
Engine:
- 2003 Chevrolet 6.0l. 364ci. “Throttle by Wireâ€
- Harness modified by Wait4Me Performance.
- All emissions and torque management removed
- Comp Cams TU1 cam
- Comp Cams 7.400 pushrods
- Comp Cams 918 springs
- ARP rod bolts
- LS6 valley cover
- Camaro oilpan, windage tray, pickup tube
Turbo System:
-Turbonetics t76 .96a/r with f1 wheel
-Stock manifolds with v bands welded on
-Synapse 60mm gate
-JGS 56mm BOV
-ETS custom intercooler
-3" downpipe dumped behind front wheel
Fuel System:
- Tanks Inc intank twin walbro 255 pumps w/ mini sump
- Stainless Steel Braided fuel lines assembled @ HoseHead Quarters
Cooling System:
- 4 core high efficiency radiator re-cored by Hi-Tech Radiator
- Lincoln Mark VIII Cooling fan
- Delta Control, fan controller
Transmission:
- 2003 GM 4L80E
- B&M Super Cooler Transmission Cooler w/ fan
Electrical:
- Low/High headlights on relays
- Complete M.A.D. electrical conversion (firewall forward)
Steering: - 1999 Jeep Grand Cherokee Power Steering box 12.5:1 Ratio
- Heim joint outer tie rod ends
- Bump Steer adjusters
Suspension:
Front:
- Coleman Racing Fabricated 9†Impala spindles
- SPC Performance fully adjustable upper control arms
- Afco Racing steel/nylon lower control arm bushings
- VariShocks Coilovers revalved by Alston/Chassisworks, 16 position adjustable
- Braced and Strapped factory lower control arms
- Factory small block sway bar
Rear:
- 12 bolt. Eaton Posi w/ 3:42 gears
- Speedway Motors axle side Panhard bar mount
- Custom frame side Panhard bar mount
- Panhard bar made w/ AllStar hex tubing w/ QA1 Heim Joints
- Lower Control arms made w/ AllStar hex tubing w/ QA1 Heim Joints
- Upper control arms are Edelbrock adjustables with Johnny Joints
Brakes:
- 2003 Cadillac Escalade Hydroboost brake assist
Front:
- C6 Z06 Corvette 14" rotors 6 piston calipers Custom 7075 hubs from Kore3
Rear:
- C6 Z06 Corvette 13" rotors 4 piston calipers
Wheels:
Front: - 2004 Corvette Z06 17†x 9.5â€
Rear: - 2004 Corvette Z06 18†x 10.5â€
Tires:
Front: - Falken 615 285/40/17
Rear: - M/T ET streets 305/35/18
Wheel Adapters: Custom machined by Trevor at Colecraft.
Interior:
Gauges: - Complete Defi Gauges mounted in custom bezel, AEM boost and air/fuel
Shifter: - B&M Pro Ratchet Shifter
Seats: - Megan Racing
Transmission Tunnel: - Custom fabricated by Greg @ HD Ornamental Iron Ltd.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0015-1.jpg&hash=79fe46fcc24eb4e9ed5adb840b979acae287bb1c)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0669.jpg&hash=b60f1653f42cd66020d7c3bcb6dbd622a6130e5e)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0670.jpg&hash=5cafbe7f92514b7474530884ffad23c0d4068840)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0848.jpg&hash=63bde66cfc3b2158f801e8d0bbe94dce020fbc18)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0849.jpg&hash=5930c5b586fc5e7a9614d4c7448ca60b09c4f6d6)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0860.jpg&hash=cdb80beacb91677195e58b9894c6c4c5703c959a)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0861.jpg&hash=7ab0c9085017b950c2ee764a0a54b435d7b1c391)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0862.jpg&hash=572e63c3315a293f75bc2238cb1a153b601948b4)
Fronts once I get more parts.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0839.jpg&hash=1848c95145f4baaf4de273d78a54f54c66aea219)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0864.jpg&hash=26bb6b3f153c11d079ccab21efd9b9fb7abdd7d2)
-
NICE
-
Damn its about time you made it over here. I was trying to find a way to contact you, glad you made it. How she runing?
-
Car is running great in the garage, we just got 6 inches of snow again, but I'm a couple grand away from driving it.
dvst8r tracked me down VIA ls1tech, hooked me up with a link.
Now I'd just like to get my join date and my post count corrected to my old username. This one is more fitting now.
Thanks guys! Really appreciate you guys wanting to see the car :)
-
Car is running great in the garage, we just got 6 inches of snow again, but I'm a couple grand away from driving it.
dvst8r tracked me down VIA ls1tech, hooked me up with a link.
Now I'd just like to get my join date and my post count corrected to my old username. This one is more fitting now.
Thanks guys! Really appreciate you guys wanting to see the car :)
Care to make another build thread for the site?
-
Car is running great in the garage, we just got 6 inches of snow again, but I'm a couple grand away from driving it.
dvst8r tracked me down VIA ls1tech, hooked me up with a link.
Now I'd just like to get my join date and my post count corrected to my old username. This one is more fitting now.
Thanks guys! Really appreciate you guys wanting to see the car :)
Care to make another build thread for the site?
For sure I will, I'll turn this into a build thread, Give me some time I'm pretty busy, will slowly toss one together for you guys
-
dam how big are those rotors? :o
-
dam how big are those rotors? :o
14" front 6 piston calipers
13" rear 4 piston calipers O0 :somb:
-
your rotors are bigger than crx wheels
hahahahhaha true that :evil:
-
Fuck ya this is one of my top HMT rides :yes: Soon as the snow is gone we need ricer smashing,tire shredding vids :evil:
-
Fuck ya this is one of my top HMT rides :yes: Soon as the snow is gone we need ricer smashing,tire shredding vids :evil:
you know me too well. this bitch is gonna get rode HARD this summer :yes:
-
Love this car, nice to see you back.
-
One of my favorite builds. Cant wait to see this thing rip again.
-
Fuck ya this is one of my top HMT rides :yes: Soon as the snow is gone we need ricer smashing,tire shredding vids :evil:
you know me too well. this bitch is gonna get rode HARD this summer :yes:
I know 90dx is going to the $10K street car shootout at the end of may @ Castrol are you gonna make a showing? One of these days once this fucking snow melts for good I will have to make a trip north to see this beast.
-
sick chevelle
-
:evil:
Makes me chub up!
-
too tight, in for updates
-
ballin :noel:
-
Love this car, those brakes are sick.
-
Love this car, those brakes are sick.
+1 At least we know she will be able to stop
-
what year is that? 72? I used to have a 67 ss ragtop with the 396...Chevelle is one of my fav Chev's and your build looks sweet :yes:
-
Love this car, those brakes are sick.
+1 At least we know she will be able to stop
It could stop last year, had 12" rotors all around. But it was Camaro rear calipers with Circle track sprint car calipers up front. Kinda pieced together setup. 1976 impala rotor/hubs. So this way I can replace the rotor without touching the hubs, over the counter parts from GM, and a solid setup. I also did a junkyard hydraboost setup years ago on the car, still on it and working awesome. No vaccum bullshit to worry about.
Yes the car is a 72 with 71 park lights. I dislike the solid amber park lights.
Check at the top I added a spec list.
-
excelllent to see this build here. what did take you so long
Beau
-
excelllent to see this build here. what did take you so long
Beau
Had no idea about the new site bro. dvst8r tracked me down and gave me the link :yes:
-
good,
now find and recruit more people with builds from oHMT
-
Had no idea about the new site bro. dvst8r tracked me down and gave me the link :yes:
we were trying to track you down and I couldn't remember your name on hmt then I got banned before I found you, welcome home! :)
-
Had no idea about the new site bro. dvst8r tracked me down and gave me the link :yes:
we were trying to track you down and I couldn't remember your name on hmt then I got banned before I found you, welcome home! :)
hahah yea I was gonna spout off but I hated the colors, made my angry so I just left.
Feels great to be home though. Big round of hugs hahaha :-* :?:lol
-
Hell yea this car is the shit
-
very cool, you should charge for rides in it!
-
That's fucking awesome.
-
One word . BAD ASS !!!! :evil: Oh that's two words
-
One of these days once this fucking snow melts for good I will have to make a trip north to see this beast.
Fuck ya take me. I'm glad somebody tracked this guy down, this car kicks some fuking ass!!
-
your car is sick as fuck.... i likey alot
-
:o That looks awesome. Yeah this weather sucks cant go out and play with the snow on the ground. Need some vids of just it up and running. Any updated pics?
-
Ripper/Wheelie Vids???
-
I have no ripper vids or real progress. School nets me no money. But I am ordering some parts tomorrow to finish up the front end. Ball joints, LCA's, coil overs, steering arms, and jounce bumps.
Relocated the coils, will have new plug wires tomorrow, I'll take some pics and a vid of the bitch running.
Thanks for all the comments guys!!!
-
a v8+boost will turn u out :noel:
-
a v8+boost will turn u out :noel:
Agreed. Gas mileage sucks ass though.
-
a v8+boost will turn u out :noel:
Agreed. Gas mileage sucks ass though.
Gotta start rating that shit in gallons per mile :?: haha
-
Been ages since I've been on here. Went to school and finished my apprenticeship. So now I'm a j-man!
Coilovers are in the mail, tubular lower control arms, Howe ball joints, and then install the front end. in 2 weeks I'll be ordering 2 18" rims for the front, 4 tires, meth kit and a shift kit. Woo hoo!!
-
Been ages since I've been on here. Went to school and finished my apprenticeship. So now I'm a j-man!
Coilovers are in the mail, tubular lower control arms, Howe ball joints, and then install the front end. in 2 weeks I'll be ordering 2 18" rims for the front, 4 tires, meth kit and a shift kit. Woo hoo!!
What trade did you take the apprenticeship for?
-
a v8+boost will turn u out :noel:
Agreed. Gas mileage sucks ass though.
only if its floored all the time.
should be better than stock cruising with the turbo always has been for me.
-
Been ages since I've been on here. Went to school and finished my apprenticeship. So now I'm a j-man!
Coilovers are in the mail, tubular lower control arms, Howe ball joints, and then install the front end. in 2 weeks I'll be ordering 2 18" rims for the front, 4 tires, meth kit and a shift kit. Woo hoo!!
What trade did you take the apprenticeship for?
Welding. Once I get my j-man card I will head back to test for my b pressure, and do in house pressure welding.
-
Nice car, hairy neck. ;D
-
Nice car, hairy neck. ;D
Hairy neck, are you local to me? lol
-
Nice car, hairy neck. ;D
Hairy neck, are you local to me? lol
http://i19.photobucket.com/albums/b183/syko_mini/100_0839.jpg (http://i19.photobucket.com/albums/b183/syko_mini/100_0839.jpg)
Isnt this the neck in question? Oh, I thought it was yours. :-[
-
Nice car, hairy neck. ;D
Hairy neck, are you local to me? lol
http://i19.photobucket.com/albums/b183/syko_mini/100_0839.jpg (http://i19.photobucket.com/albums/b183/syko_mini/100_0839.jpg)
Isnt this the neck in question? Oh, I thought it was yours. :-[
lol beard, neck hair. All the same I guess lol
-
Not that this is really worth it. BUT I ordered my hallman incab boost controller, 2 new 18" wheels for the front. And the front suspension is still in the mail. Should be on the road in roughly 30 days.
-
Not that this is really worth it. BUT I ordered my hallman incab boost controller, 2 new 18" wheels for the front. And the front suspension is still in the mail. Should be on the road in roughly 30 days.
It's gonna miss the $10,000 street car shoot out. :'(
-
Not that this is really worth it. BUT I ordered my hallman incab boost controller, 2 new 18" wheels for the front. And the front suspension is still in the mail. Should be on the road in roughly 30 days.
It's gonna miss the $10,000 street car shoot out. :'(
I know, but I'll be up there with 3 10 second cars, 2 9 second cars all from the same family. Along with many other friends reppin strong. there should be a handful of LS swaps there. Give me a shout and we can meet up!
-
Not that this is really worth it. BUT I ordered my hallman incab boost controller, 2 new 18" wheels for the front. And the front suspension is still in the mail. Should be on the road in roughly 30 days.
It's gonna miss the $10,000 street car shoot out. :'(
I know, but I'll be up there with 3 10 second cars, 2 9 second cars all from the same family. Along with many other friends reppin strong. there should be a handful of LS swaps there. Give me a shout and we can meet up!
Brett is being shitty and decided he would rather go riding than watch fast street cars at Castrol.
-
Not that this is really worth it. BUT I ordered my hallman incab boost controller, 2 new 18" wheels for the front. And the front suspension is still in the mail. Should be on the road in roughly 30 days.
It's gonna miss the $10,000 street car shoot out. :'(
I know, but I'll be up there with 3 10 second cars, 2 9 second cars all from the same family. Along with many other friends reppin strong. there should be a handful of LS swaps there. Give me a shout and we can meet up!
Brett is being shitty and decided he would rather go riding than watch fast street cars at Castrol.
I haven't committed either way, but at this point the dodge won't be done so it will probably be Castrol.
-
You should post up the vid of the lumpy cam :noel:. Great build.
-
Nice!! Synapse wg are the shit O0
-
Got some good and bad news.
The good:
Hallman in cab boost controller is installed
AEM progressive meth kit is installed
All front suspension work and brakes installed/blead
Tires bought
Shift kit goes in, in approx 12 days.
The bad:
Have to wait on new coils for the coilovers, spring rate is too soft
Retard with my rims, marked them as pool parts, and undervalued them. They got caught at customs in a random inspection. Looking at rims and reading pool parts doesn't add up. Along with the value. Retard I bought the rims from never told me he was going to pull a stunt like that, nor did I ask him too. Fuck brain. Sooo 9 day wait now.
Here are some pictures.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0982.jpg&hash=b1355680537eb2128e84347d178cda1d426522a9)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0983.jpg&hash=6e0cea29b79f583baabc10e14a573205aaea5c21)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0984.jpg&hash=986074a7d7d4f1a7a498b2b91b829171a822cf9c)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0988.jpg&hash=72aa10cd9d110a45a2bc070cdf739c4904e3e5a9)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0992.jpg&hash=5efbc966159365f6281d8377b7350275e96955fd)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_0997.jpg&hash=fae4423a3d8c83e7ff2b55a4ba992e736eaa4ce1)
-
This car is so amazing!
-
Too bad you weren't in Sask, my friend has a 506bb in his 71 Velle SS, 600 motor, 750 bottle. git sum :yes:
-
Too bad you weren't in Sask, my friend has a 506bb in his 71 Velle SS, 600 motor, 750 bottle. git sum :yes:
I'd love to come play. I'd race a school bus, hell I'd even race a kid in his sneakers!
I aint scurrred O0
-
Damn your a baller!!!
-
Thanks bud!!!
Rims came in today. Get tires mounted in the AM tomorrow. Coilover springs will be here tomorrow. Hopefully go for a drive tomorrow!!!
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_1037.jpg&hash=e899bf38e5fd5bedd5f58801aaf460aa30ab2d56)
-
same rim painted black?
shit looks good black though
essentially...
factory z06 corvettes come staggered 17x9.5 front and 18x10.5 rear. Minimum I can run in the front now is 18. So I had to get a repo 18x9.5. They are dirt cheap in black so I went with them. I'll get my other ones coated later on. But for now I'm going to rock front black and rear gunmetal O0 True gangsta
-
Got the new springs and tires mounted. Drove the car out of the garage. Gets registration tomorrow. it really needs a tune hahaha.
-
heres a quick pic
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_1039.jpg&hash=f88551759b5c014650e4eaa6d77d935f163fed52)
-
Trade you for my vette
-
Trade your car for my girlfriend
-
baller
-
Trade your car for my girlfriend
Done!
-
pics of vette and girlfriend hahah
So I drove it tonight. On 7lbs it feels faster then it was on 15lbs lol. roll in 2nd gear at 80km/h, no issues skating around. 3rd gear, same story.
Then my night ended on a flat bed home. Ignition part in the column broke. Some pot metal piece of shit. Sooo parents felt bad for no birthday present for the past 2 years and overnighted me a ididit stainless column.
Pics/vids to come.
-
pics of vette and girlfriend hahah
So I drove it tonight. On 7lbs it feels faster then it was on 15lbs lol. roll in 2nd gear at 80km/h, no issues skating around. 3rd gear, same story.
Then my night ended on a flat bed home. Ignition part in the column broke. Some pot metal piece of shit. Sooo parents felt bad for no birthday present for the past 2 years and overnighted me a ididit stainless column.
Pics/vids to come.
Is that with the new cam?
-
383 419rwhp/476rwtq
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fwww.dragcityvideos.com%2Fimages%2F96corvette%2F96corvette_24.jpg&hash=4860a4742d81d0153249a9fd81483d94e0b4f4cd)
-
^^Ahh a bit lost are you?
-
^^Ahh a bit lost are you?
thats what you get for having such dreamy eyes
-
Solid rig brother!!!!
Column should be here tomorrow.
Yes it was with the new cam. Sounds horny. I'll get video for sure. Tomorrow night I'm off to edmonton to take the ecu and get the new tune dumped on it. Upgraded timing tables, increase injector recovery rate on decel in idle, increase rev limiter, and increase idle air. Along with some minor touch ups.
-
increase injector recovery rate on decel in idle
can you go into more detail? Iam unsure what this does? cheers
-
increase injector recovery rate on decel in idle
can you go into more detail? Iam unsure what this does? cheers
Theres a name for it. But what is happening. Is when I roll up to a red light, stop sign or stop. The idle drops down to where it should idle, and the injectors are not squirting fast enough to save the idle. How it was explained to me was you can adjust how fast the injectors react, the slower the rate, the more linear, the fast, the less linear. So theres a fine line. This problem is also associated with too much cam and not enough idle air flow. So all this should hopefully be fixed tonight.
On that note... FUCK Summit Racing. I payed for 1-2 day freight. Not lets let the column sit around for a day, package it and ship it out at 5 the NEXT fucking day. So monday it is. Fox Creek. Retards.
-
So the car is back on the road. Started raining 20 minutes into the cruise. SOn of a bitch. Ohwell. updates to follow. Just wanted to update saying everything went in nice. Althought Ididit puts their key position in a retarded postion. 5 o clock is stupid for a key.
-
What would you say the limits are on the stock block? My 03 yukon is dieing for some boost :evil:
-
Whos tuning it in Edmonton? That place is such a cunt hole.
-
Whos tuning it in Edmonton? That place is such a cunt hole.
+1
-
Whos tuning it in Edmonton? That place is such a cunt hole.
+1
A buddy of mine owns Horsepower Solutions. He tuned it for me.
Stock long block.... I'd keep it tame around the 450rwhp range. Put rod bolts and valve springs in and turn it up to low 500's.
Remember.... My kit at 7psi last year made 475rwhp and 67xftlbs!!!
-
Here are some pics guys. Boost gauge isn't reading right or something. 11psi spring in the synapse gate, yet I only see 6psi on the gauge. Plumbed from gauge to intake. Perhaps my problem???
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_104844.jpg&hash=59687191bc0ed8a176911b6440cc2fdb6290ae7a)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_104622.jpg&hash=0c9c6b1a84fa14b9394949bd3cc824830f1fe4cf)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_104711.jpg&hash=37d7a5e46d956ffc1fc3a8d5cc6449c58550bb5e)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F100_104933.jpg&hash=e59fb7bafc30591dc1033a1a04ab41816b512357)
-
Car looks bad ass!
-
I really need to make it up north one of these weekends and see this thing in person.
-
I really need to make it up north one of these weekends and see this thing in person.
Doo it!
Thanks for the comments guys. Kinda getting tired of the no traction issues so I'm pricing out Strange SS series drag brakes for the rear. Going to a 15x10 beadlock drag wheel with a drag radial. Goin 10.5 style with the car.
-
I love all that tread under that car, the stance is just Tough. really fucking cool ride.
-
so I'm alive. Life is busy. But....
The car went 11.25@129 last night. 1.9 60foot haha. Stock torque converter on bald 18" drag radials.
Tranny is finally shitting the bed after 4 years of abuse on a bone stock 4l80 out of a pickmeup truck.
Gonna toss a 3400 or 3600 stall in it over winter, 10.5" slicks on 15" beadlocks, build the tranny, and new valve springs. trying to get some pics and video uploaded.
-
how does that turbo spool? i am trying to pick a turbo for a v8 and i am lost. i am thinking single turbo on the smaller side for a chevy 350 cause it will be for a truck to tow my racecar.
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
-
how does that turbo spool? i am trying to pick a turbo for a v8 and i am lost. i am thinking single turbo on the smaller side for a chevy 350 cause it will be for a truck to tow my racecar.
I would do the t3/t4 turbo from a t-bid manual trans. There available and work well on lower boost applications and the spool fairly quick.
.60 intake
.63 exhaust
-
too small of an exhaust housing, get the fuck out of this thread with that shit. ask in general discussion.
-
good too see an update i liked the build thread at the other shit hole.
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
-
too small of an exhaust housing, get the fuck out of this thread with that shit. ask in general discussion.
why didnt i think of that? make a thread to ask him how his turbo spools, BRILLIANT!!!!!
-
Love the car glad to see it still running!
-
how does that turbo spool? i am trying to pick a turbo for a v8 and i am lost. i am thinking single turbo on the smaller side for a chevy 350 cause it will be for a truck to tow my racecar.
Full boost by 3400.
I'd do a 67mm or 70mm. Masterpower t70 or a turbonetics t67
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
your absolutely right. cragers amongst many other 60-70's era wheels can be had for pretty cheap. I think I paid like $200 for a set of craigers that needed some polish at a swap meet. and I know you could probably have 2 full panels of NICE autometers for the price of those defis/sensors. And the seats...some factory buckets would suit me.
again, I love your car, just those few little things that bug me.
-
Only thing that bugs me is that it has too small f a turbo on it... :yes:
-
how does that turbo spool? i am trying to pick a turbo for a v8 and i am lost. i am thinking single turbo on the smaller side for a chevy 350 cause it will be for a truck to tow my racecar.
Full boost by 3400.
I'd do a 67mm or 70mm. Masterpower t70 or a turbonetics t67
thanks for the info, i will go a little smaller then. i have no plans of revving it much over 5k and i want power right out of the hole
-
I would do the t3/t4 turbo from a t-bid manual trans. There available and work well on lower boost applications and the spool fairly quick.
.60 intake
.63 exhaust
T-bird didnt come with a t3/t4 hybrid. In fact, no car came with that hybrid turbo period. The Garrett turbo that came on the tbird was a 60trim t3.
-
Only thing that bugs me is that it has too small f a turbo on it... :yes:
There was talk about 2, or 1 larger single. Either way gonna change the piping up me thinks. More front mount style.
-
s400 plz O0
-
S510.
-
s400 plz O0
s400 is fucking huge for a t6 frame. Bahh. how about a t6 frame precision 88?
-
I would do the t3/t4 turbo from a t-bid manual trans. There available and work well on lower boost applications and the spool fairly quick.
.60 intake
.63 exhaust
T-bird didnt come with a t3/t4 hybrid. In fact, no car came with that hybrid turbo period. The Garrett turbo that came on the tbird was a 60trim t3.
my bad thats right ts on a t3 frame with either a .63 or a .48 exhoust housing.
-
s400 plz O0
s400 is fucking huge for a t6 frame. Bahh. how about a t6 frame precision 88?
88mm = Dandy
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
your absolutely right. cragers amongst many other 60-70's era wheels can be had for pretty cheap. I think I paid like $200 for a set of craigers that needed some polish at a swap meet. and I know you could probably have 2 full panels of NICE autometers for the price of those defis/sensors. And the seats...some factory buckets would suit me.
again, I love your car, just those few little things that bug me.
cragers went out of style 20 years ago.
i think the z06 wheels look kinda cool on that car.
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
your absolutely right. cragers amongst many other 60-70's era wheels can be had for pretty cheap. I think I paid like $200 for a set of craigers that needed some polish at a swap meet. and I know you could probably have 2 full panels of NICE autometers for the price of those defis/sensors. And the seats...some factory buckets would suit me.
again, I love your car, just those few little things that bug me.
cragers went out of style 20 years ago.
i think the z06 wheels look kinda cool on that car.
oh come on man! Cragers never go out of style, they are synonymous with classic.. Its like saying "Blowjobs are out of style, Rim jobs is where its at." Its apples to Rim jobs dude, totaly different.
-
Looks like I am going to be at a Dyno day in Red Deer on Saturday. It is at Canada Custom Vehicles. You should drop by with the chevelle.
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
your absolutely right. cragers amongst many other 60-70's era wheels can be had for pretty cheap. I think I paid like $200 for a set of craigers that needed some polish at a swap meet. and I know you could probably have 2 full panels of NICE autometers for the price of those defis/sensors. And the seats...some factory buckets would suit me.
again, I love your car, just those few little things that bug me.
rawr, since he deleted his account, wishes me to point out that you are a fucking moron and Craigers couldn't accomodate those brakes. I suggest you agree with rawr and STFU, or he will sign back up and send you gay porn.
That is all.
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
your absolutely right. cragers amongst many other 60-70's era wheels can be had for pretty cheap. I think I paid like $200 for a set of craigers that needed some polish at a swap meet. and I know you could probably have 2 full panels of NICE autometers for the price of those defis/sensors. And the seats...some factory buckets would suit me.
again, I love your car, just those few little things that bug me.
cragers went out of style 20 years ago.
i think the z06 wheels look kinda cool on that car.
(not to hotrex this thread)
kinda cool fits the statement well. I also mentioned "many other wheels" in my statement
idk, maybe if the car was painted or something. :-\
-
I love and hate this car all at the same time. Engine/suspension/brakes/car is pure tits.
The crappy megan seats and the defis do not fit the car one bit.
Just my $.02. Also, not much of a fan of the wheels either.
Thats perfectly fine. Thats why there are so many other companies on the market. To please people such as yourself and myself. I think the wheels go great on the car. If I had some more coin the wheels would be powder coated black in the rear aswell. But I roll based on my paychecks. Not a visa with an unreal limit.
your absolutely right. cragers amongst many other 60-70's era wheels can be had for pretty cheap. I think I paid like $200 for a set of craigers that needed some polish at a swap meet. and I know you could probably have 2 full panels of NICE autometers for the price of those defis/sensors. And the seats...some factory buckets would suit me.
again, I love your car, just those few little things that bug me.
cragers went out of style 20 years ago.
i think the z06 wheels look kinda cool on that car.
(not to hotrex this thread)
kinda cool fits the statement well. I also mentioned "many other wheels" in my statement
idk, maybe if the car was painted or something. :-\
To each their own. I think it looks deadly with the black wheels and massive brakes behind them. Fucking cookie cutter Boyds, American Racing, etc etc. If I had the budget they would be Forged race line of wheels. But at 1500 a wheel minus rubber.... No thanks.
-
Looks like I am going to be at a Dyno day in Red Deer on Saturday. It is at Canada Custom Vehicles. You should drop by with the chevelle.
I will swing by. I know a couple employees. But the transmission is only good for cruising and minor bag session. Dyno's sketch me out when its a strictly horsepower only setup especially with it on the way out. No computer to tell me what my line pressures are doing or slip = not cool.
-
your car is tits i love it... stall is gonna cost you a pretty penny whats the price on 1 for the 4l80 now days.. i priced them this time last year and it made me change my mind into going with a th400..
here are a few cars my friend has done around the town i live in..
GT-47 LSX 240sx (http://www.youtube.com/watch?v=6FuFE7O4ifE#normal)
chevy 2 twin turbo (http://www.youtube.com/watch?v=P_4Id2iDq6M#normal)
i think yours is my fave though..
-
your car is tits i love it... stall is gonna cost you a pretty penny whats the price on 1 for the 4l80 now days.. i priced them this time last year and it made me change my mind into going with a th400..
here are a few cars my friend has done around the town i live in..
GT-47 LSX 240sx (http://www.youtube.com/watch?v=6FuFE7O4ifE#normal)
chevy 2 twin turbo (http://www.youtube.com/watch?v=P_4Id2iDq6M#normal)
i think yours is my fave though..
Right on! That Chevy 2 is titts. And a 4 gear car too!!
Stalls are 1000 fucking dollars. I may go TH400, if I find a good deal.
-
your car is tits i love it... stall is gonna cost you a pretty penny whats the price on 1 for the 4l80 now days.. i priced them this time last year and it made me change my mind into going with a th400..
here are a few cars my friend has done around the town i live in..
GT-47 LSX 240sx (http://www.youtube.com/watch?v=6FuFE7O4ifE#normal)
chevy 2 twin turbo (http://www.youtube.com/watch?v=P_4Id2iDq6M#normal)
i think yours is my fave though..
Right on! That Chevy 2 is titts. And a 4 gear car too!!
Stalls are 1000 fucking dollars. I may go TH400, if I find a good deal.
Fuck that shit, go find somebody who rebuilds converters. If they know what they are doing it wouldnt be a big deal to modify a stock one.
-
you could just get it re-stalled but its not gonna be nearly as strong.
u wanna sell the 4l80 my roommate is looking for 1.. Hotrod power tour is gonna suck in a 3 speed lol so he wants either a 4l80 or a gear vender and the 80 is alot cheeper..
-
I have been looking at the 4speed gm auto and or put in a manual 5 speed there i know what gear im in..
http://cgi.ebay.com/ebaymotors/700R4-4L60E-HIGH-STALL-TORQUE-CONVERTER-HD_W0QQcmdZViewItemQQhashZitem1ddfe6364QQitemZ8019403620QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories (http://cgi.ebay.com/ebaymotors/700R4-4L60E-HIGH-STALL-TORQUE-CONVERTER-HD_W0QQcmdZViewItemQQhashZitem1ddfe6364QQitemZ8019403620QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories)
What type of trans controller do you have?
After last weekend at the track my stall converter is rattling inside when i idle. Put slight load in gear it goes away and no the torque convert bolts arent loose i checked already.
Right on! That Chevy 2 is titts. And a 4 gear car too!!
Stalls are 1000 fucking dollars. I may go TH400, if I find a good deal.
your car is tits i love it... stall is gonna cost you a pretty penny whats the price on 1 for the 4l80 now days.. i priced them this time last year and it made me change my mind into going with a th400..
here are a few cars my friend has done around the town i live in..
GT-47 LSX 240sx (http://www.youtube.com/watch?v=6FuFE7O4ifE#normal)
chevy 2 twin turbo (http://www.youtube.com/watch?v=P_4Id2iDq6M#normal)
i think yours is my fave though..
-
your car is tits i love it... stall is gonna cost you a pretty penny whats the price on 1 for the 4l80 now days.. i priced them this time last year and it made me change my mind into going with a th400..
here are a few cars my friend has done around the town i live in..
GT-47 LSX 240sx (http://www.youtube.com/watch?v=6FuFE7O4ifE#normal)
chevy 2 twin turbo (http://www.youtube.com/watch?v=P_4Id2iDq6M#normal)
i think yours is my fave though..
Right on! That Chevy 2 is titts. And a 4 gear car too!!
Stalls are 1000 fucking dollars. I may go TH400, if I find a good deal.
Fuck that shit, go find somebody who rebuilds converters. If they know what they are doing it wouldnt be a big deal to modify a stock one.
We've run stock stalls rebuilt and they usually net 20% slip on the top end. I'll pay the cash for a Neal Chance converter. Built around my car and my engine setup.
On a buddies twin turbo ls mustang, a off the shelf stall was 19% slip on the top end. 9.8@144 if I remember right. With the new converter from Neal Chance the car went 9.52@148. Pretty nice gains for changing nothing else and 6-8% slip on the top.
-
For a thousand dollars I want more than three tenths and four mph.
-
you could just get it re-stalled but its not gonna be nearly as strong.
Links please. Ive seen stock converters (ford mind you) run low 6's in the 1/8th for multiple seasons.
Converters balloon from idiots jacking the pressure to the moon on "built" transmissions with a redrilled valvebody and shimmed accumulators. The aftermarket supports what people think they want, not what they need.
But hey, if you want to spend the $$$ its your car.
For a thousand dollars I want more than three tenths and four mph.
Couldnt a few more pounds of boost accomplish this sir?
-
For a thousand dollars I want more than three tenths and four mph.
Couldnt a few more pounds of boost accomplish this sir?
Absolutely not, I won't have people saying I'm poor and had to up the boost.
-
For a thousand dollars I want more than three tenths and four mph.
Couldnt a few more pounds of boost accomplish this sir?
Absolutely not, I won't have people saying I'm poor and had to up the boost.
Hide the boost controller in the crankcase vent box. No-one will know. :noel:
-
For a thousand dollars I want more than three tenths and four mph.
Couldnt a few more pounds of boost accomplish this sir?
Absolutely not, I won't have people saying I'm poor and had to up the boost.
Hide the boost controller in the crankcase vent box. No-one will know. :noel:
But I will know, Robb. It's hard to sleep at night with $1000 worth of cash on my conscience.
-
For a thousand dollars I want more than three tenths and four mph.
Have to be there and run the stuff to know I guess. A stock restalled stall will not take you to 8's. It will drive like complete and utter shit on the road. Have any of you guys drove in a vehicle with a neal chance or other high end converter? They drive like a completely stock stall, until you lay into it. Not this high revving bullshit to drive around. Thats left for relic, cockaroach machines.
-
you could just get it re-stalled but its not gonna be nearly as strong.
Links please. Ive seen stock converters (ford mind you) run low 6's in the 1/8th for multiple seasons.
Converters balloon from idiots jacking the pressure to the moon on "built" transmissions with a redrilled valvebody and shimmed accumulators. The aftermarket supports what people think they want, not what they need.
But hey, if you want to spend the $$$ its your car.
For a thousand dollars I want more than three tenths and four mph.
Couldnt a few more pounds of boost accomplish this sir?
All it does is blow through the converter worse. Running through the traps at 6800rpm in a LS is up there on a stock junkyard build 6.0l. Traps do not change one bit with more boost.
-
For a thousand dollars I want more than three tenths and four mph.
Have to be there and run the stuff to know I guess. A stock restalled stall will not take you to 8's. It will drive like complete and utter shit on the road. Have any of you guys drove in a vehicle with a neal chance or other high end converter?
I like to make smartassed comments.
There's a reverse manual valvebody Procharged Mustang at the shop I've driven a bit, I know what a good setup feels like.
-
I gues i still am doing the cheap setup home made turbo style. I will step up this time and let some else build my trans only because i want overdrive. I dont feel to comfortable with doing the 700r4/4l60e i have done 2 and they worked but i had issues with the seals and drum springs. Can get a bilt 700r4/4l60e from a company for 1300 with 2400 stall converter and he boastes it will hold up to some serious power.
cadracer,
If you are going to be racing I would not sell you a Level 2 you need a Level 3. Our Level 3 700R4, with torque converter up to 2400 stall (no nitrous use) shipping to you in WA to any business address dyno tested and in a real nice crate is $1350. Call us so we can discuss your application in more detail.
Remember the transmission is only as good as the builder, even if you are using all top of the line components. There is a lot more than just exchanging parts when remanufacturing a transmission. I have been rebuilding high performance, racing and daily driver transmissions for over 26 years and I am a man with integrity. One thing for sure, you will not be disappointed. I am always available to provide technical assistance to help ensure that we setup the right transmission and torque converter for your application.
We build bulletproof transmissions! It is critical that we know how you are running your vehicle and the needs you have for your application. If you're running nitrous, superchargers or turbo-chargers, please be sure to give us this information. We cannot setup the right transmission for your application without this information.
or i will just put in this manual 6 speed trans
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=360195079915&viewitem=&sspagename=STRK%3AMEWAX%3AIT (http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=360195079915&viewitem=&sspagename=STRK%3AMEWAX%3AIT)
-
Yeah, converters are particular to what power adders you run, if any.
-
you could just get it re-stalled but its not gonna be nearly as strong.
Links please. Ive seen stock converters (ford mind you) run low 6's in the 1/8th for multiple seasons.
Converters balloon from idiots jacking the pressure to the moon on "built" transmissions with a redrilled valvebody and shimmed accumulators. The aftermarket supports what people think they want, not what they need.
But hey, if you want to spend the $$$ its your car.
For a thousand dollars I want more than three tenths and four mph.
Couldnt a few more pounds of boost accomplish this sir?
i they said it for me : )
-
Remember the transmission is only as good as the builder, even if you are using all top of the line components. There is a lot more than just exchanging parts when remanufacturing a transmission. I have been rebuilding high performance, racing and daily driver transmissions for over 26 years and I am a man with integrity. One thing for sure, you will not be disappointed. I am always available to provide technical assistance to help ensure that we setup the right transmission and torque converter for your application.
We build bulletproof transmissions! It is critical that we know how you are running your vehicle and the needs you have for your application. If you're running nitrous, superchargers or turbo-chargers, please be sure to give us this information. We cannot setup the right transmission for your application without this information.
This is what I like about slushomagics. You really can build one that will hold a million fucking horsepower and actually have it last (probably longer than the motor).
-
For a thousand dollars I want more than three tenths and four mph.
Have any of you guys drove in a vehicle with a neal chance or other high end converter? They drive like a completely stock stall, until you lay into it. Not this high revving bullshit to drive around. Thats left for relic, cockaroach machines.
Yes. I have an 8" converter in my mustang, ordered as a 4k stall, goes to 5k on the TB. but driving around town, and on the highway it sits in the 25-3500 range cruising nicely even with 4.56's.... till you wack it. ;) Its a good feeling.
-
So, what stall would you guys run in a TH400 mated to a 800 whp K24A4?
-
So, what stall would you guys run in a TH400 mated to a 800 whp K24A4?
whatever happened to that s2k with an f20 or 22 and a powerglide that was on OHMT a few years ago?
-
th400 is parasitic overkill for a k24, a 350 or a 475 will take care of that power level no problem
TH350 will keel over past 600-650, unless you're replacing the internals with $$$.
I'm really not worried about sub-50 whp parasitic loss.
-
So, what stall would you guys run in a TH400 mated to a 800 whp K24A4?
4000 ish. IF a "Track car" (Drag) polssibly a TAD higher
-
yeah i would have to agree on the t-400 instead of the 350 stouter internals. Also i would use a 3600 to 4k stall because boost will drive it to probably 5. Look into a trans break valve body you will wish you had it after the fact i am.
;D
-
So, what stall would you guys run in a TH400 mated to a 800 whp K24A4?
did i miss a thread/link, or are you really asking this general of a question?
edit: I'd love to know more about the combo
-
So, what stall would you guys run in a TH400 mated to a 800 whp K24A4?
did i miss a thread/link, or are you really asking this general of a question?
edit: I'd love to know more about the combo
Well, you take a Honda K24 and bolt a turbo and a TH400 to it. I've got the tune part down, but IDK anything about stalls. Help pls.
-
Where do you expect the motor to start making a shit load of tq at??? Insert stall speed... Higher tq will raise stall of a said converters rating a bit.. TH400 with 8" 4500 stall converter and reverse manual valvebody with brake please... If its gonna be driven on the street I wouldnt go any higher... SHould be interesting when it locks up a bit... HAHAHAHHA In a car that light??? OOOOHHHH MMMMMMMM GEEEEEEEEEEEEEEEEEEE
Fuck I think Im wet.....
-
My friend has a 71 Chevelle SS w/ a 506, and a mild built TH350 trans, that car is fucking wild.
-
Well, you take a Honda K24 and bolt a turbo and a TH400 to it. I've got the tune part down, but IDK anything about stalls. Help pls.
Well, where does it make power?? and more importantly as has been pointed out.. torque?? stall speed is affected by the power you have and don't have. It is also possible have a converter out of the power band (on either side) and it will be lazy. I'd say you want it just on the verge of where it really starts to build power, but have enough stall so that it can actually build boost without moving the car. It's a lot different than a clutch, and you no longer need(or have) inertia to as great of an extent. say for example when you shift, what is the lowest in the rpm band you would like the car to go? that is probably close to your desired stall speed.
[also if you're having a converter built, i'd like it to have an anti-ballooning plate, and a to a lesser extent a billet cover(which is actually the back) would do wonders in helping it not explode.]
-
I'd say you want it just on the verge of where it really starts to build power
This is what I have always been told by the old-skool ford guys at work.
The Nova has a 3200rpm stall, but it came with the trans so thats what we ran. It will fucking move off the line.
-
bump
-
bump
-
Bump with low-12's youtube sleeper...
I'd say you want it just on the verge of where it really starts to build power
This is what I have always been told by the old-skool ford guys at work.
The Nova has a 3200rpm stall, but it came with the trans so thats what we ran. It will fucking move off the line.
Record Breaking Minivan! (http://www.youtube.com/watch?v=RifBFGQoTes#normal)
Good people to ask, more than enough Turbo Dodge ppl running autos...
-
Car is still with me. Work, new truck, girlfriend, shit like that is putting stuff on hold. Plus a cold garage.
I now have HP tuners, new lap top. MSD boost controller. Moser c clip elims with 1/2" studs. Weld 15x10 alumastars double beadlocked, all the old turbo setup sold, and some misc odds and ends.
-
Car is still with me. Work, new truck, girlfriend, shit like that is putting stuff on hold. Plus a cold garage.
I now have HP tuners, new lap top. MSD boost controller. Moser c clip elims with 1/2" studs. Weld 15x10 alumastars double beadlocked, all the old turbo setup sold, and some misc odds and ends.
So whats the new setup looking like?
-
Car is still with me. Work, new truck, girlfriend, shit like that is putting stuff on hold. Plus a cold garage.
I now have HP tuners, new lap top. MSD boost controller. Moser c clip elims with 1/2" studs. Weld 15x10 alumastars double beadlocked, all the old turbo setup sold, and some misc odds and ends.
So whats the new setup looking like?
Looks like nothing. It'll be a secret until I have the force fed power in my hands lol.
-
hmmmm
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F012.jpg&hash=e0c31294bd6deb9e210fe323b595940a2fd59778)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F013.jpg&hash=f3e7a02d2f28c2d2c20ffcc8530ca154c16fd6dc)
-
I hear you sold off your cool v-band welded truck manifolds. Building something cooler? ;)
-
I hear you sold off your cool v-band welded truck manifolds. Building something cooler? ;)
lol who told you?
-
I hear you sold off your cool v-band welded truck manifolds. Building something cooler? ;)
lol who told you?
The performance community in Alberta is smaller then one would think... It was just a grapevine rumor until now. Some one (honestly can't remember if it was mike or luke that told me) thought they saw them on a zephyr build.
-
love this build...updates? come on!
by the way the tial wg u sold me works flawless...thanks again
-
I hear you sold off your cool v-band welded truck manifolds. Building something cooler? ;)
lol who told you?
The performance community in Alberta is smaller then one would think... It was just a grapevine rumor until now. Some one (honestly can't remember if it was mike or luke that told me) thought they saw them on a zephyr build.
Lol thats hilarious. Yea they are on my buddies twin t-70 lsx zephyr now.
I dont have much progress right now. Dropping the centers and rings off to get anodized black tomorrow. Other shit is in the mail. Going to look at/buy some more fittings and shit tomorrow.
-
love this build...updates? come on!
by the way the tial wg u sold me works flawless...thanks again
Fuck yea, that was the black one correct?
-
Rear end setup changeing?? Dont look like the WELDS will clear the brakes.
-
Rear end setup changeing?? Dont look like the WELDS will clear the brakes.
Yes sir. Strange brakes in the rear. Pull the rear end out, weld the axle tubes. Put c clip elims on. Install back into car.
-
Can we have more pic's! I love this car :yes:
-
Robb just offered me a high mileage but clean Outback for ~$1000, first thing that came to my mind was your car and an LSx swap - I love the Subaru chassis, but the drivetrain is crap.
-
Can we have more pic's! I love this car :yes:
I honestly have no more pics lol. I am getting a nice shipment in on monday that a I will take pics of. hah
-
Robb just offered me a high mileage but clean Outback for ~$1000, first thing that came to my mind was your car and an LSx swap - I love the Subaru chassis, but the drivetrain is crap.
Theres 2 ls swapped wrx's on ls1tech. Fucking giver. You can find 6.0l for 700 bucks any day of the week in wreckers. or a 5.3 with a z06 cam for 500. Do that shit up
-
Robb just offered me a high mileage but clean Outback for ~$1000, first thing that came to my mind was your car and an LSx swap - I love the Subaru chassis, but the drivetrain is crap.
Theres 2 ls swapped wrx's on ls1tech. Fucking giver. You can find 6.0l for 700 bucks any day of the week in wreckers. or a 5.3 with a z06 cam for 500. Do that shit up
i was just reading about those a couple days ago..
too bad they couldnt keep the awd..
-
Robb just offered me a high mileage but clean Outback for ~$1000, first thing that came to my mind was your car and an LSx swap - I love the Subaru chassis, but the drivetrain is crap.
Theres 2 ls swapped wrx's on ls1tech. Fucking giver. You can find 6.0l for 700 bucks any day of the week in wreckers. or a 5.3 with a z06 cam for 500. Do that shit up
IDK... I'm not feeling it this morning. Maybe if you posted up some sweet burnouts to inspire me I might change my mind? :P
too bad they couldnt keep the awd..
There aren't many AWD vehicles that are as fast in a straight line or on a road course unless you have R34 or 911TT money. The Subaru shit would simply fall apart under the abuse with LSx torque thrown into the mix, so why bother? A correctly set up aluminum block LSx Scooby would fucking flay the flat four failures, and be cheaper too.
-
Robb just offered me a high mileage but clean Outback for ~$1000, first thing that came to my mind was your car and an LSx swap - I love the Subaru chassis, but the drivetrain is crap.
Theres 2 ls swapped wrx's on ls1tech. Fucking giver. You can find 6.0l for 700 bucks any day of the week in wreckers. or a 5.3 with a z06 cam for 500. Do that shit up
IDK... I'm not feeling it this morning. Maybe if you posted up some sweet burnouts to inspire me I might change my mind? :P
too bad they couldnt keep the awd..
There aren't many AWD vehicles that are as fast in a straight line or on a road course unless you have R34 or 911TT money. The Subaru shit would simply fall apart under the abuse with LSx torque thrown into the mix, so why bother? A correctly set up aluminum block LSx Scooby would fucking flay the flat four failures, and be cheaper too.
i realize the stock awd setup would be total fail with LSx power, but living in the asshole of the universe where we generally get fuckloads of snow for what seems like half a year, AWD is more appealing... i also realize it would have to be custom parts, (as if the LSx isnt) but from what i read there is no room at all no matter what you have...
that sir, is my reasoning behind it.
-
The civette rocks out in the corners very well. Straight line too, so you could properly setup up the scooby swap.
Here are 2 videos of my buddies rides. Low 9 second rides, 147mph and 148mph. S10 is 2 12" subs, ac, power windows, spare tire, etc etc. Full factory trim. 4000lbs. 88mm precision, a/w, nitrous, etc. Mustang is a twin 70mm 6.0l. meth, a/a. etc.
LS1 S10 (http://www.youtube.com/watch?v=ja7pu6oz0eM#normal)
1 fast car, 1 slow car=Still a lot of spinning (http://www.youtube.com/watch?v=CqQvX0uj1tk#normal)
-
i realize the stock awd setup would be total fail with LSx power, but living in the asshole of the universe where we generally get fuckloads of snow for what seems like half a year, AWD is more appealing...
Lots of power + AWD = fail in the snow. Keep your winter beater stock, and don't worry how the toy goes in the snow?
-
damn i see a piece of rubber straight shooting off the tire at like 35 seconds in that last vid there.
-
damn i see a piece of rubber straight shooting off the tire at like 35 seconds in that last vid there.
Looks like a blower belt to me.
-
i realize the stock awd setup would be total fail with LSx power, but living in the asshole of the universe where we generally get fuckloads of snow for what seems like half a year, AWD is more appealing...
Lots of power + AWD = fail in the snow. Keep your winter beater stock, and don't worry how the toy goes in the snow?
where is you sense of adventure???
-
i think s10s are gay but fuck that thing is crazy
-
where is you sense of adventure???
It ran off with my hair.
-
lolz Jew
-
damn i see a piece of rubber straight shooting off the tire at like 35 seconds in that last vid there.
Looks like a blower belt to me.
Ok ok, no more dick pictures from me.
The belt is just the alt/waterpump belt. I believe he was 7400rpm on that pull, spun it waay too high and it chucked the belt.
-
Ok this order came in a couple days ago. Next pay day I'll order the material to build the manifolds.
Precision billet wheeled 67mm units. Tial MVS 38mm v band gates and Tial Q bov.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F001.jpg&hash=859b10d8be838dd3a3f4526648612b68fd160784)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F010.jpg&hash=7b14163e055625dfb6a02b9f473eb26b6d4287b0)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F006.jpg&hash=46efb8e1b33b01fe5331c4bc91cdf9bd6b3de154)
Oh yea, and I got this 70 Acadian 327/m22 car. The body looks rough, but is damn straight and rust free. Probably the same or less amount of rust as my Chevelle. Best part.... FREE. My uncle gave it to me. Plenty of vintage correct performance parts. Probably do a similar build to the Chevelle.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F176.jpg&hash=e22701ff6b14451371c87d44af865cd5af6a2249)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F164.jpg&hash=20a6cea28ee2b74776ee332e7063bbf04c4e82d4)
-
NICE!
-
I FUCKING HATE YOU
i have wet dreams about 68-72 Nova's, for real id probably sell Body parts for one. Kinda not kidding. Fuck a kidney i got 2 of em.
-
A pair of 67mm's, I like where this new build is headed! I assume with those you are shooting for 4 digit power. I really need to make it up to Red Deer this year to see this in person, I am moving an hour's drive closer though in a couple weeks (from okotoks, to airdrie).
-
Baller as always. We just need more pic's!!!!!!!!!!!!!!!!!!!!
-
A pair of 67mm's, I like where this new build is headed! I assume with those you are shooting for 4 digit power. I really need to make it up to Red Deer this year to see this in person, I am moving an hour's drive closer though in a couple weeks (from okotoks, to airdrie).
Run it semi hard for the year, and then near the end probably put an ad in the for sale section titled "Yard Sale" and I will list whatever I chuck out of the stock block hahha
Kill mode? I prefer to call it |yard sale mode"
We are shooting for 8xxrwhp. Who knows. Its been done. I was in the 650 mark last year on 11-14lbs on the 76mm. Had false knock all year though, even on race gas.
-
A pair of 67mm's, I like where this new build is headed! I assume with those you are shooting for 4 digit power. I really need to make it up to Red Deer this year to see this in person, I am moving an hour's drive closer though in a couple weeks (from okotoks, to airdrie).
Run it semi hard for the year, and then near the end probably put an ad in the for sale section titled "Yard Sale" and I will list whatever I chuck out of the stock block hahha
Kill mode? I prefer to call it |yard sale mode"
We are shooting for 8xxrwhp. Who knows. Its been done. I was in the 650 mark last year on 11-14lbs on the 76mm. Had false knock all year though, even on race gas.
Your just sick! Make me want to turbo my 03 yukon :yes:
-
love this build...updates? come on!
by the way the tial wg u sold me works flawless...thanks again
Fuck yea, that was the black one correct?
yes sir!
-
Your just sick! Make me want to turbo my 03 yukon :yes:
DO ET!
-
Your just sick! Make me want to turbo my 03 yukon :yes:
DO ET!
She has 123k on her right now. I think a Hx-55 would be sweet and tons of flux cord :evil: Just not sure what injectors or what ems to use?
-
I bet JD knows what EMS to use.
-
I bet JD knows what EMS to use.
Where is that niggerface how he lovenly call me over a text :P
-
I bet JD knows what EMS to use.
there was another text not long ago he was talking about using EFI live, and how well it worked, even compared to LSx standalones such as BS3 and what not..
http://www.realhomemadeturbo.com/forum/index.php?topic=12318.0 (http://www.realhomemadeturbo.com/forum/index.php?topic=12318.0)
i may not post alot... but i do read and suprisingly remember... alot
-
honestly efi llive or hp tuners for anything under 1000rwhp.
motron 60lb injectors. 400 beans. Plug and playISH. 40 bucks for ls1 car injector plugs and some 3/8" hard line to space the fuel rails 1/2" up.
-
There are ways to rescale the MAF in order to make more than 1000 whp.
-
There are ways to rescale the MAF in order to make more than 1000 whp.
yea IE run speed density O0 sy/ty IAT sensor wired into factory maf wiring. 2 bar / 3 bar map up top. Done.
Thats what I did. Thats what many guys do aswell. I follow what works well.
-
honestly efi llive or hp tuners for anything under 1000rwhp.
motron 60lb injectors. 400 beans. Plug and playISH. 40 bucks for ls1 car injector plugs and some 3/8" hard line to space the fuel rails 1/2" up.
Hum you have me thinking now :evil:. What you think the stock 4wd trans is good for hp/tq wise?
-
There are ways to rescale the MAF in order to make more than 1000 whp.
yea IE run speed density O0 sy/ty IAT sensor wired into factory maf wiring. 2 bar / 3 bar map up top. Done.
Thats what I did. Thats what many guys do aswell. I follow what works well.
Operating from a Ford-based perspective, and having no GM experience beyond OBD1, that's not what I was thinking. But it is probably the best method for that application.
-
There are ways to rescale the MAF in order to make more than 1000 whp.
yea IE run speed density O0 sy/ty IAT sensor wired into factory maf wiring. 2 bar / 3 bar map up top. Done.
Thats what I did. Thats what many guys do aswell. I follow what works well.
Operating from a Ford-based perspective, and having no GM experience beyond OBD1, that's not what I was thinking. But it is probably the best method for that application.
We ls guys up in Canada like tuning SD more so then MAF. Yes you can get away with the MAF but it is soo much simpler. 2 less clamps, easier piping, etc etc. Along with MAF can act up. Even N/A I had issues with my MAF getting wet in rain and making the car run like shit. (I run no inner fenders)
-
honestly efi llive or hp tuners for anything under 1000rwhp.
motron 60lb injectors. 400 beans. Plug and playISH. 40 bucks for ls1 car injector plugs and some 3/8" hard line to space the fuel rails 1/2" up.
Hum you have me thinking now :evil:. What you think the stock 4wd trans is good for hp/tq wise?
the 4l60 isn't much of a tranny to be honest. I would put a transgo HD2 kit in it before I drove it boosted. Thats the downfall. 4l60s are expensive to build to handle abuse aswell. :(
-
I was wondering if it was a 4L60.
Throw an upgraded sun shell in it as well.
-
There are ways to rescale the MAF in order to make more than 1000 whp.
yea IE run speed density O0 sy/ty IAT sensor wired into factory maf wiring. 2 bar / 3 bar map up top. Done.
Thats what I did. Thats what many guys do aswell. I follow what works well.
I guess I never heard of the GM sensors working well. Working, but not well. I guess it doesn't matter when you can just throw displacement at the problem :P
-
There are ways to rescale the MAF in order to make more than 1000 whp.
yea IE run speed density O0 sy/ty IAT sensor wired into factory maf wiring. 2 bar / 3 bar map up top. Done.
Thats what I did. Thats what many guys do aswell. I follow what works well.
I guess I never heard of the GM sensors working well. Working, but not well. I guess it doesn't matter when you can just throw displacement at the problem :P
You are hanging out with the wrong people then. Never once had an issue with a GM Cobalt SS 2 bar Map. GM 3 bar map. Syclone IAT sensor, etc etc. Not once.
-
Got the rear end out. Gonna wash it, weld the axle tubes, cut the ends off, put c clip elims on. get those pressed onto the moser axles. Put new 5/8 wheel studs in, paint it. Slam it back in. Wait for brakes to sell then buy new ones.
Got my rims back from powder coat. Mounting new drag radials 275/60/15.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F002.jpg&hash=ab12b30aec90a0b801511703b619eabc31c8af86)
Also got a new RCI fuel cell. Foam, baffled, sumped, and has a fuel level sender.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F004-1.jpg&hash=f13f3e52c9141c034c3cfc61e330a26206f73a4d)
Also bought a Aeromotive A1000 fuel pump and filter.
Acestainless order is in the mail.
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
-
Should put real slicks and do some wheelies :evil:
-
Should put real slicks and do some wheelies and barrel rolls :evil:
-
Should put real slicks and do some wheelies and twist the windows out of it :evil:
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
-
Should put real slicks and do some wheelies and twist the windows out of it :evil:
anti roll bar in the rear will prevent this :) if it hangs them, it will hang them dead even.
-
All this shinny new shit and v-band everything makes my pee pee hard and drippy!
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Right on. why a 10 wide rim? You said you had to sacrifice brakes for it could you have gotten away with an 8?
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Shhhhhh... Dont tell Johnny.
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Right on. why a 10 wide rim? You said you had to sacrifice brakes for it could you have gotten away with an 8?
Sounds slightly hypocritical but it isn't. A 10" wide rim allows the widest possible footprint available when running a 275/60/15 tire. 8" Works, and it works well but you gain more contact patch with the added 2 inches.
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Shhhhhh... Dont tell Johnny.
Its the truffs!
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Right on. why a 10 wide rim? You said you had to sacrifice brakes for it could you have gotten away with an 8?
Sounds slightly hypocritical but it isn't. A 10" wide rim allows the widest possible footprint available when running a 275/60/15 tire. 8" Works, and it works well but you gain more contact patch with the added 2 inches.
why would a wider rim make a wider contact patch? would that be all on the tire? a 275 is 275 mm wide regarless of what rim its one isnt it? Not trying to argue just tryin to understand.
-
I think what he MIGHT be saying is that the wider rims allows for more surface footprint where as a less diameter rim would cause the tire to lose that X mm amount due to slack that is left around the sidewall. In other words, just because the tire measures xxx mm in diameter, you are not necessarily taking advantage of the size unless you have the rim width to do so
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Right on. why a 10 wide rim? You said you had to sacrifice brakes for it could you have gotten away with an 8?
Sounds slightly hypocritical but it isn't. A 10" wide rim allows the widest possible footprint available when running a 275/60/15 tire. 8" Works, and it works well but you gain more contact patch with the added 2 inches.
why would a wider rim make a wider contact patch? would that be all on the tire? a 275 is 275 mm wide regarless of what rim its one isnt it? Not trying to argue just tryin to understand.
Redcav is correct. on a 8" rim you lose footprint because the rim being narrower is actually pulling tread around the side to try and turn it into sidewall now. With the 10" wide rim, it is pulling the sidewalls as far apart as safely possible(Mickey Thompson tech) thus creating more footprint width. This setup us about the most true and most stable way of getting the full footprint of your tire O0
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Right on. why a 10 wide rim? You said you had to sacrifice brakes for it could you have gotten away with an 8?
Sounds slightly hypocritical but it isn't. A 10" wide rim allows the widest possible footprint available when running a 275/60/15 tire. 8" Works, and it works well but you gain more contact patch with the added 2 inches.
why would a wider rim make a wider contact patch? would that be all on the tire? a 275 is 275 mm wide regarless of what rim its one isnt it? Not trying to argue just tryin to understand.
Redcav is correct. on a 8" rim you lose footprint because the rim being narrower is actually pulling tread around the side to try and turn it into sidewall now. With the 10" wide rim, it is pulling the sidewalls as far apart as safely possible(Mickey Thompson tech) thus creating more footprint width. This setup us about the most true and most stable way of getting the full footprint of your tire O0
Thus not being a tire stretching homo VW guy and adding more rubber for give and grip for less spin
-
Now that makes sense. Cool.
-
ehh got some work done. I'll probably finish getting the wastegate routing done this weekend, then weld this one out. Rinse and repeat. Coping pipe is fucking LAME.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F001-3.jpg&hash=d86eea14babe22a70ac244a2a3beb3de02d0fb7f)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F004-3.jpg&hash=1a36620f1d29d23f2d1ec451d8fbc85eedaf3269)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F002-2.jpg&hash=8b8eaed5130f24fcaee175246581b56f4d0f9b77)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F005-2.jpg&hash=d933dc3c9844af4b1e16337b56e873e2e9ee6d77)
-
ME LIKEE
-
ME LIKEE
Thanks bud!
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Some one care to explain why some muscle cars have fucking HUGE slicks? Then you say that and i wonder why they have those absolutly gigantic slicks on the back of a car.
-
275? seems small for all you got going on aren't those deep rims? Id try to stuff as much rubber as you can under neath that thing lol.
275/60/25 on a 15x10 wheel is going deep 7's now. Full tubbed, big tire, Big block carbed junk times are gone. This is the new era of racing boys.
Some one care to explain why some muscle cars have fucking HUGE slicks? Then you say that and i wonder why they have those absolutly gigantic slicks on the back of a car.
Big slicks in general are a crutch. For people that throw a set of ladder bars or comp engineering 4 link kit into the car and think that it will work great with a big tire. Where fact is, A honest and thought out suspension setup based from factory stuff WORKS. Leaf spring Camaros...Cal tracs goin deep 8s. factory 4 link cars such as my chevelle? Johnny joints, rubber bushings, heim joints, anti roll bar, and drag shocks. DONE. It works. deep 8's aswell.
Plus some people just love it for some reason.
My fathers friend has a 68 Camaro. aftermarket 4 link, full tub with matching goodyear slicks, lumpy ass big block 50Xci. Race gas, trans brake, massive stall, can't afford to street drive it but does. Solid lifters so adjusting the valves every other cruise.(not quite but close). Everyone thinks its a bad mother fucker. They play it off as if it is. But when it comes down to things... The car runs 12.5's. WTF? I foot brake a 11.2 with a stock tranny/converter LOL
-
...Big slicks in general are a crutch... or comp engineering 4 link kit into the car and think that it will work great with a big tire.
I am doing this right now. :-* But it is going in a truck not a car. :P
-
...Big slicks in general are a crutch... or comp engineering 4 link kit into the car and think that it will work great with a big tire.
I am doing this right now. :-* But it is going in a truck not a car. :P
lol just make it fast. All I ask :)
-
Got one manifold comleted. Both flanges got machined flat so no leak issues. Got my wilwood rear brakes today. They will go on this weekend me thinks. Rear fender lips trimmed off(tire clearance). Water line/steam pocket line kit installed. Fuel cell mounted, fuel fittings on order, and some other shit.
Pictures are way cooler then typing.
Manifold
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F005-3.jpg&hash=bc609bb1f69ee411889ac4c840c607e96b3470ea)
Another angle
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F006-2.jpg&hash=d96353cd3912b6f496a388776308a99320bddc6e)
38mm mvs tial gate dump tube. My order was screwed up and they sent the wrong size reducers, so I slammed them on hahah
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F007-1.jpg&hash=27f4f0f45a122e2d6e0e58c73e8e5cf68395be8a)
overall
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F010-1.jpg&hash=660efe611fa3362836560426a9876a88771594cc)
dump
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F013-1.jpg&hash=d72e976fee4eee816a6249fb1a3941337b725bb1)
car
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F001-4.jpg&hash=1c6c0a9ca52dd0674c382fb2cc46a6fdaa9b2415)
-
I like the setup alot, and I love the look of it all, but the only thing that I dont really car for is how the dump on the wg points at the front tire. I dont think it will cause any problems but if it were my car and with my luck I would burn a little oil and shoot it all over my front tires tread and crash.
Other than that I love this buid. V8+boost= teh Sex!
I cant wate to start building my tt truck someday!
-
I like the setup alot, and I love the look of it all, but the only thing that I dont really car for is how the dump on the wg points at the front tire. I dont think it will cause any problems but if it were my car and with my luck I would burn a little oil and shoot it all over my front tires tread and crash.
Other than that I love this buid. V8+boost= teh Sex!
I cant wate to start building my tt truck someday!
I know what you are saying, I ran it like that for well over a year and never had an issue. I can also spin it right around and point at the ground like most doo.
-
totaly forgot about the whole v-band thing....lol
Right on. I dont know why, but on every open wg dump tube Ive ever made I always put turndowns on them.
-
totaly forgot about the whole v-band thing....lol
Right on. I dont know why, but on every open wg dump tube Ive ever made I always put turndowns on them.
I should grab another pic aswell. Its not nearly as bad as the pic makes it out to be. I like turn downs but it makes a fuck of a mess doing street pulls. Its a street cleaner, and it also is a huge heat score for doing any type of pull with potential people behind me. I should just put horns on it. lol
-
totaly forgot about the whole v-band thing....lol
Right on. I dont know why, but on every open wg dump tube Ive ever made I always put turndowns on them.
lol yea v bands are a love hate. Awesome when they are flat. LAME when they are warped hahaha
-
heres a video from last year. I saw the toyota boys having a meet so I showed up. Decent quality of me driving the car how I always do lol.
Red Deer JDM Toyotas + Insane Chevelle (http://www.youtube.com/watch?v=vGVmi5GjIFo#lq-lq2-hq-vhq)
-
Nice burnout. ;D
-
Hum smoky burn out just how I like :noel:
-
I want one ;D
-
love the dump exit location
-
love the dump exit location
Funny you mention that, I ended up changing it, there was just too much weight way out on the gate and dump off the manifold. Slightly changed. I fnished up both manifolds tonight with gates and gate dumps. Only thing I'm not happy about, but I will change it next winter....The drivers side head is further back then the passenger side, so the identical length manifolds make one turbo sit more forward then the other. Ohwell. Minor detail.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F004-4.jpg&hash=1f0bd6328fcb9dc6da946baa16763ab8551de935)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F006-3.jpg&hash=db564d138e89c481c18f1ec5d5f6b1c00e9e86d7)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F009-1.jpg&hash=5bb53477d9812f5c4a588b154561cd3040320586)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F008.jpg&hash=64f3122a036d6b060c0c604779b4f1cef5d8a65e)
this pic makes it look horrible, its about .75" back from the other side.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F007-2.jpg&hash=f7f16a5f46a635126a371de91c51bbd4dceb7b4d)
-
That is sexy. :yes: ;D
-
Good work, now more smoky burn outs!
-
That makes my peepee hard.
-
That makes my peepee hard.
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
BDV where are your vids? You always claim your rapping on your slut and yet you fail with vids.
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
BDV where are your vids? You always claim your rapping on your slut and yet you fail with vids.
HMT mini boat anchor fest (http://www.youtube.com/watch?v=TtWBjy8UvUM#lq-hq-vhq)
your welcome brian
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
yea I had no say in the music, hell I really didn't know I was in the film. I did it for the girlfriend at the time in the car hahahha
car sounds bad ass spiker! 3rd gear, I approve.
BDV where are your vids? You always claim your rapping on your slut and yet you fail with vids.
HMT mini boat anchor fest (http://www.youtube.com/watch?v=TtWBjy8UvUM#lq-hq-vhq)
your welcome brian
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
yea I had no say in the music, hell I really didn't know I was in the film. I did it for the girlfriend at the time in the car hahahha
car sounds bad ass spiker! 3rd gear, I approve.
BDV where are your vids? You always claim your rapping on your slut and yet you fail with vids.
HMT mini boat anchor fest (http://www.youtube.com/watch?v=TtWBjy8UvUM#lq-hq-vhq)
your welcome brian
About time we see a vid from the nog.
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
BDV where are your vids? You always claim your rapping on your slut and yet you fail with vids.
I have yet to see anyhting form you period nigger... I fdont really worry about vids, nor trust everyone on this site. There are some, but they sure as fuck wont be posted in GD... That vid is like 2 yrs old lol...
I always did like that part where we are on the freeway and 3rd gets dirtied and pedaled and after the shift to 4th leed is like SPIKER.
LOL
-
Like the smoke from the wheelspeed after 2nd gear.
That video is gay in all aspects except for polychlorinatedbifunnels.
WHAT IN THE FUCK IS THAT "music"
BDV where are your vids? You always claim your rapping on your slut and yet you fail with vids.
I have yet to see anyhting form you period nigger... I fdont really worry about vids, nor trust everyone on this site. There are some, but they sure as fuck wont be posted in GD... That vid is like 2 yrs old lol...
I always did like that part where we are on the freeway and 3rd gets dirtied and pedaled and after the shift to 4th leed is like SPIKER.
LOL
You have yet to see anything from me, because I always built cars for other people. I have yet to build something worth showing. I posted my broke mans build thread, and when its done you shell see tons of dirty 3rd's :noel:
-
that vid is super old and shity....
-
that vid is super old and shity....
truth
-
that vid is super old and shity....
truth
I like it :yes:
-
Add; http://www.realhomemadeturbo.com/forum/index.php?topic=435.msg5800#msg5800 (http://www.realhomemadeturbo.com/forum/index.php?topic=435.msg5800#msg5800)
BTW what are the new turbos?
-
Add; http://www.realhomemadeturbo.com/forum/index.php?topic=435.msg5800#msg5800 (http://www.realhomemadeturbo.com/forum/index.php?topic=435.msg5800#msg5800)
BTW what are the new turbos?
thanks bro! turbos are precision 6765 billet wheels
-
any more vids of this beast in action?
-
Well finally got it running. Oil pan pulled off and tapped, new plug wires, downpipes done, bungs galore for widebands, gates and dumps done, brakes bled and working, blah blah blah. Drove it out of the garage last night, sounds pretty nasty with the dumps hahah. Now off to get the intercooler piping done. And yes I have a cable to tie up lol
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F001-6.jpg&hash=2c3c864c7a216a5138eb6661cecb57a21466bff8)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F002-4.jpg&hash=2a86ee297850f7f1e5327f86a15a3e029609b4d0)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F003-5.jpg&hash=e9bebfeb100dcc45b5bdc97daa0ad5c2ebf3c397)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F005-5.jpg&hash=31057c1320e1643843b8f1be0a1165f2615c67ab)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F006-4.jpg&hash=30d7867b055f902ac381ce08463cc65a93e9f5a9)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2F009-2.jpg&hash=1b7ea337a7741324ff4756ed45094cc861fb1629)
-
damn all that tire out back sure lookls bigger than 275 in the pics. straight nasty.
fapfapfapfapfapfapfap
-
I don't think it's a sleeper anymore...
-
Sick.
-
Lookin great!
-
its fun. haha 3600 stall going in soon.
Some photographer took a couple pics. One really shows the body damage my grandpa did, and the fender I turned inside out, and the rust hahah.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2Ftwinchevelle.jpg&hash=9909fc2f5801f2ef0b7582e6c336d5c8e0dc6c55)
And this one shows the nice water spots haha
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi19.photobucket.com%2Falbums%2Fb183%2Fsyko_mini%2Ftwinturboshovel.jpg&hash=c38dc95b73976c712c0c76475cd45c7e90e6a11b)
YEAAA nig nogs.
Its loud as fuck.
-
Oh PS, not like its a huge kill, but I fucking MURDERED a GTR skyline, the new one. whatever they are called.
-
The name you are looking for is slow.
-
Have you raced this yet?
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG00215-1.jpg&hash=904e244d7a6a7647f60d18c307bb9e80afd38263)
-
that thing looks like it would stand em up
-
Have you raced this yet?
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG00215-1.jpg&hash=904e244d7a6a7647f60d18c307bb9e80afd38263)
Lots, its a really good friends of mine. It went 9.25@147 on the 2nd pass out.
I still havn't hooked up my boost controller yet so I'm still on 8lbs. He is on 12-14 when I raced him. Its a fully built 370. Ported heads by an unreal guy in edmonton(all of his all motor, pump gas cars are low 9 second High 8 second jerico shifted cars). We tugged atleast 8 times, 8 lbs to 8lbs they are pretty fucking close, skating around I stay with him or pull on him, and when his is hooked on higher boost it pulls away hard like it should lol. We will be going for 8s in his car after the long weekend.
-
275X?
-
275X?
275/60/15 on both cars. Nothing bigger, nothin smaller. RADIAL TIRE CARS TO THE FRONT MOTHERFUCKER!!!
-
Ah, so you're on the 275 bandwagon without taking part in the class. That's odd.
-
Ah, so you're on the 275 bandwagon without taking part in the class. That's odd.
Only way to roll. Why in the fuck would I narrow my frame to mini tub it? big tires are fucking lame. Does my car have a cage? Does it lack lots of stuff? Yup. Is there a 275 class anywhere near me? Nope.
Call it what you want but big tires are for faggets and I support the 275 class 100%.
-
That Zephyr is win
-
Ah, so you're on the 275 bandwagon without taking part in the class. That's odd.
Only way to roll. Why in the fuck would I narrow my frame to mini tub it? big tires are fucking lame. Does my car have a cage? Does it lack lots of stuff? Yup. Is there a 275 class anywhere near me? Nope.
Call it what you want but big tires are for faggets and I support the 275 class 100%.
The boss' 275X car was built to be an 8.5" Outlaw. He'll be at the import vs domestic shootout with it, and the Civic.
The only thing we have tubbed with big tires - currently - is the S2000 powered '71 Datsun. Would you like the shop number so you can tell him he's a faggot?
-
Ah, so you're on the 275 bandwagon without taking part in the class. That's odd.
Only way to roll. Why in the fuck would I narrow my frame to mini tub it? big tires are fucking lame. Does my car have a cage? Does it lack lots of stuff? Yup. Is there a 275 class anywhere near me? Nope.
Call it what you want but big tires are for faggets and I support the 275 class 100%.
The boss' 275X car was built to be an 8.5" Outlaw. He'll be at the import vs domestic shootout with it, and the Civic.
The only thing we have tubbed with big tires - currently - is the S2000 powered '71 Datsun. Would you like the shop number so you can tell him he's a faggot?
what are you trying to convey here? I think that its way more fun/cool to get a car in the 6-7s on a small tire then it is a huge relic tire.
I've told many people that own big tire cars that knock small tire cars what I think about it. Next time you are playing around with your race team, weigh a 10.5 slick and your relic 33" slick. Do the rotating mass calculations to see how much is on the table. Maybe stop by a chassis setup school to learn how to set the car up on a smaller tire.
-
Ah, so you're on the 275 bandwagon without taking part in the class. That's odd.
Only way to roll. Why in the fuck would I narrow my frame to mini tub it? big tires are fucking lame. Does my car have a cage? Does it lack lots of stuff? Yup. Is there a 275 class anywhere near me? Nope.
Call it what you want but big tires are for faggets and I support the 275 class 100%.
The boss' 275X car was built to be an 8.5" Outlaw. He'll be at the import vs domestic shootout with it, and the Civic.
The only thing we have tubbed with big tires - currently - is the S2000 powered '71 Datsun. Would you like the shop number so you can tell him he's a faggot?
what are you trying to convey here? I think that its way more fun/cool to get a car in the 6-7s on a small tire then it is a huge relic tire.
I've told many people that own big tire cars that knock small tire cars what I think about it. Next time you are playing around with your race team, weigh a 10.5 slick and your relic 33" slick. Do the rotating mass calculations to see how much is on the table. Maybe stop by a chassis setup school to learn how to set the car up on a smaller tire.
What I was trying to say is that you have an awful lot of hate for something that simply works, while simultaneously bandwagoning the hot affordable DR class without participating in it. It's kind of like saying you hate Mazdas (#1 most roadraced chassis) while building a spec racer by the rulebook that you'll never compete on a road course with. Me, personally, i just like cars. :-\
How are you controlling your power so that you can hook on that 275 tire, anyway? Goforth's cut some 5.6@126-128 with a 1.2 60' on that tire in an 1100 whp 3200lb chassis, he'd do a lot better if he had a 7135 box.
-
Ah, so you're on the 275 bandwagon without taking part in the class. That's odd.
Only way to roll. Why in the fuck would I narrow my frame to mini tub it? big tires are fucking lame. Does my car have a cage? Does it lack lots of stuff? Yup. Is there a 275 class anywhere near me? Nope.
Call it what you want but big tires are for faggets and I support the 275 class 100%.
The boss' 275X car was built to be an 8.5" Outlaw. He'll be at the import vs domestic shootout with it, and the Civic.
The only thing we have tubbed with big tires - currently - is the S2000 powered '71 Datsun. Would you like the shop number so you can tell him he's a faggot?
what are you trying to convey here? I think that its way more fun/cool to get a car in the 6-7s on a small tire then it is a huge relic tire.
I've told many people that own big tire cars that knock small tire cars what I think about it. Next time you are playing around with your race team, weigh a 10.5 slick and your relic 33" slick. Do the rotating mass calculations to see how much is on the table. Maybe stop by a chassis setup school to learn how to set the car up on a smaller tire.
What I was trying to say is that you have an awful lot of hate for something that simply works, while simultaneously bandwagoning the hot affordable DR class without participating in it. It's kind of like saying you hate Mazdas (#1 most roadraced chassis) while building a spec racer by the rulebook that you'll never compete on a road course with. Me, personally, i just like cars. :-\
How are you controlling your power so that you can hook on that 275 tire, anyway? Goforth's cut some 5.6@126-128 with a 1.2 60' on that tire in an 1100 whp 3200lb chassis, he'd do a lot better if he had a 7135 box.
Just because theres a big tire doesn't mean its always fast. I street drive my car more then your boss does, nor do I have the pocket book of his. I want to get it done ona 275 tire that also happens to be affordable to. Even if I had the money I would not be a big tire car. For the racing here, I'm stock suspemsion, stock frame. Thus no added points. Thanks!
MSD boost controller. Works great. Map my progressive ramp rate. done.
-
Here are some new pics. Did a race overhaul on my trans and installed the yank 3600 converter. Totally different car!!
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG_1889.jpg&hash=ba0d1b301c47865fa59adbd6443dfcfba558ce18)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG_1892.jpg&hash=6f45f58b3d3caa28b91cd20486a53a787c1dc692)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG_1893.jpg&hash=5acdec3be0face6da0b9d071e36067240b0720ce)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG_1897.jpg&hash=6026a1d00f933113364c5a0a6df6f6fa63c3bd5f)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi10.photobucket.com%2Falbums%2Fa142%2Ftirefryin_s10%2FIMG_1899.jpg&hash=c6404b9ff4c961c86d39f9bbf6addd3024859d19)
man did we every abuse the living hell out of them sunday night once my trans was done haha
-
i want to see some steet racing vids... now :yes:
-
Here are some new pics. Did a race overhaul on my trans and installed the yank 3600 converter. Totally different car!!
man did we every abuse the living hell out of them sunday night once my trans was done haha
No vids Sir?
:-[ :'(
-
Here are some new pics. Did a race overhaul on my trans and installed the yank 3600 converter. Totally different car!!
man did we every abuse the living hell out of them sunday night once my trans was done haha
No vids Sir?
:-[ :'(
Not yet :( soon I will be able to get some!
-
Bump.
I know you ran this weekend. I saw your buddy with the zephyr doing his licencing pass's on Saturday night, and I saw your car when I was on the road out. I was riding passenger or I would have swung back in and said hi.
I know the zephyr hit the 8's, how did you fair?
-
Bump.
I know you ran this weekend. I saw your buddy with the zephyr doing his licencing pass's on Saturday night, and I saw your car when I was on the road out. I was riding passenger or I would have swung back in and said hi.
I know the zephyr hit the 8's, how did you fair?
Zephyar is now a consistant 8.70 car @ 155ish mph haha. The thing is a monster dumpin the laundry out back each pass now LOL.
I managed a 10.90@126 on 8-9ish lbs of boost. Having issues with the boostcontroller, got it sorted, then got booted for the year with no cage hahaha.
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
We need pic's!
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
We need pic's!
Around xmas you will get them.
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
We need pic's!
Around xmas you will get them.
>:(
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
We need pic's!
>:(
Around xmas you will get them.
Not my money being spent, not my pics to share, I am just doing the building, and some of the driving.
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
We need pic's!
>:(
Around xmas you will get them.
Not my money being spent, not my pics to share, I am just doing the building, and some of the driving.
That makes since.
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
hahahah xoxo.
bring it to vegas for the street car supernationals. Cheeeyea!
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
hahahah xoxo.
bring it to vegas for the street car supernationals. Cheeeyea!
Not a car nor really for street. I will still be able to be tagged if we so desire, but the filled block might not like to cruise around so much.
-
I thought maybe you had died with the lack of updates. :P
Guess you better get a cage in that bitch. My big tire "faggotry" will probably get on the dyno around xmas, and goto phoenix for the races in March.
hahahah xoxo.
bring it to vegas for the street car supernationals. Cheeeyea!
Not a car nor really for street. I will still be able to be tagged if we so desire, but the filled block might not like to cruise around so much.
The name makes a person think the event is something else. There was a blown chevy truck, blue going high 6's last year.
-
Sweet, we won't be that fast. Not enough motor or chassis.
So what did you run when they kicked you off the track?
-
Bump.
I know you ran this weekend. I saw your buddy with the zephyr doing his licencing pass's on Saturday night, and I saw your car when I was on the road out. I was riding passenger or I would have swung back in and said hi.
I know the zephyr hit the 8's, how did you fair?
Zephyar is now a consistant 8.70 car @ 155ish mph haha. The thing is a monster dumpin the laundry out back each pass now LOL.
I managed a 10.90@126 on 8-9ish lbs of boost. Having issues with the boostcontroller, got it sorted, then got booted for the year with no cage hahaha.
Thing is freaken moving!
-
Sweet, we won't be that fast. Not enough motor or chassis.
So what did you run when they kicked you off the track?
It was bullshit, I went 10.90@126mph one friday night, the next sunday was our event(albertas fastest street car shootout), the tech said, "last friday you went too fast twice, youre done for the year"
So I was choked, No warning at all. Follow your own fucking rules first, GOOF.
-
That's lame. Time to build a cage.
-
Will they let you recertify it if you cage it?
-
Will they let you recertify it if you cage it?
yea
-
Update?
-
?
-
Welll Im still alive. Here are some updated pics. This piece of shiat went 9.55@144 on 17psi. 1.64 60'.
Still abusing the crap out of it. Had to rebuild the precision turbos as they were using oil. Alamo Turbos did a kick ass job. Flawless so far! Installed a PTC 9.5" converter. Best 1100 spent on this car ever.
All twin turbo cars in this pic...
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2F557022_10153026904505117_1992745087_n_zpsd7fdd70a.jpg&hash=74095375c9d25214aff951d9c0c885beacda113c)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2F182941_10151641657380751_1878842948_n_zpsc3e65849.jpg&hash=2e31868d0eef2ab07b355864646a659598034d7a)
Underhood
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2F576643_10151641657245751_775215989_n_zps01024208.jpg&hash=02488a91d7db03618235535f553974dad08a6a7e)
Full 3.5" exhaust with an x pipe. Out the back bitches. None of this dumped at the diff, smells like exhaust all the time shit. lol
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2Ftailpipe_zps666c95d5.jpg&hash=1e668d16c370c87d4798ce09e5f0b25da0f41cac)
-
Good to see your still around. You still in Red Deer? One of these days we will have to grab a beer. O0
I saw Neil out at the track a number of times this summer, but I didn't see your Chevelle, that I can recall.
-
Good to see your still around. You still in Red Deer? One of these days we will have to grab a beer. O0
I saw Neil out at the track a number of times this summer, but I didn't see your Chevelle, that I can recall.
Im living in Red Deer on my days off and in Edmonton while Im working out in RedWater.
The Chevelle hasn't been to Castrol yet. Im thinking next Friday. Have to do IHRA licensing passes though before I run it out harder. Kinda gay, ohwell.
Yea Neil has been out a fair bit, still trying to sort the car out. Too much weight in the rear. Car just wants to power wheelie all of the time.. Hasn't got his 7second pass on Canadian soil yet :(. 7.54 in vegas though!
-
Yeah I was out there with "boostedwagon" from here with his civic a few Friday's ago when Neil went 8.0x at Castrol. So close yet so far.
Are you welding out by Redwater? Mostly just drilling out that way as far as I know of.
-
this thing is awesome. just went threw the whole post again. realized i have never told you how cool i think it is.
good work. :noel:
-
Yeah I was out there with "boostedwagon" from here with his civic a few Friday's ago when Neil went 8.0x at Castrol. So close yet so far.
Are you welding out by Redwater? Mostly just drilling out that way as far as I know of.
Theres a couple kick ass turbo civics around this area. Neil did a dyno day and there was 3-4 well over 500fwhp. Last Friday a pretty nasty integra was there trapping 129mph if I remember right.
Im inspecting at the Williams/Pembina Plant. We are wrapping up an expansion and getting ready for the next one. In a 1km radius its nuts here. North West Upgrader put a call out for 2500 tradesman for their expansion which is within a km of our plant.
-
this thing is awesome. just went threw the whole post again. realized i have never told you how cool i think it is.
good work. :noel:
Thanks!!
-
this thing is awesome. just went threw the whole post again. realized i have never told you how cool i think it is.
good work. :noel:
Thanks!!
I actually just did the same and agree 100%, I'm in the process of de-hondaing and going to build a ls nova. might need some tech support! ever come to bc? lol.
-
Yeah I was out there with "boostedwagon" from here with his civic a few Friday's ago when Neil went 8.0x at Castrol. So close yet so far.
Are you welding out by Redwater? Mostly just drilling out that way as far as I know of.
Theres a couple kick ass turbo civics around this area. Neil did a dyno day and there was 3-4 well over 500fwhp. Last Friday a pretty nasty integra was there trapping 129mph if I remember right.
Im inspecting at the Williams/Pembina Plant. We are wrapping up an expansion and getting ready for the next one. In a 1km radius its nuts here. North West Upgrader put a call out for 2500 tradesman for their expansion which is within a km of our plant.
That is what boostedwagon trapped as well, but was out of gear, hopefully will go mid 130's with a new final drive.
Sweet, sounds like a good gig. My contracting stuff fell way off, so I picked up a real job, and just do a bit of lease building when called these days.
-
Goood shit. Love this car
-
Fuck yea!!!
Glad to see it running strong!
-
Goood shit. Love this car
^this^
Any new vids?
-
this thing is awesome. just went threw the whole post again. realized i have never told you how cool i think it is.
good work. :noel:
Thanks!!
I actually just did the same and agree 100%, I'm in the process of de-hondaing and going to build a ls nova. might need some tech support! ever come to bc? lol.
Actually I do haha. I have lots of friends in the Kelowna area.
-
Did you build the motor, if I recall right the motor was hurt last update?
-
Yeah I was out there with "boostedwagon" from here with his civic a few Friday's ago when Neil went 8.0x at Castrol. So close yet so far.
Are you welding out by Redwater? Mostly just drilling out that way as far as I know of.
Theres a couple kick ass turbo civics around this area. Neil did a dyno day and there was 3-4 well over 500fwhp. Last Friday a pretty nasty integra was there trapping 129mph if I remember right.
Im inspecting at the Williams/Pembina Plant. We are wrapping up an expansion and getting ready for the next one. In a 1km radius its nuts here. North West Upgrader put a call out for 2500 tradesman for their expansion which is within a km of our plant.
That is what boostedwagon trapped as well, but was out of gear, hopefully will go mid 130's with a new final drive.
Sweet, sounds like a good gig. My contracting stuff fell way off, so I picked up a real job, and just do a bit of lease building when called these days.
What are you doing for work now?? What car does boostedwagon have?
-
Goood shit. Love this car
^this^
Any new vids?
Actually heres an entertaining video... We were doing speed runs with some RC's. Fastest pass was 104mph lol. I didn't see the slash next to me. Just wanted to do a huge melter, 3rd gear... would have grabbed 6th if I had one.
https://www.youtube.com/watch?v=RRjBZTTOwPk&feature=youtube_gdata_player (https://www.youtube.com/watch?v=RRjBZTTOwPk&feature=youtube_gdata_player)
-
Did you build the motor, if I recall right the motor was hurt last update?
Yup hurt the last motor. This one is another 115,000km junk yard 6.0l with rod bolts, head studs, ls9 headgaskets and a custom cam.
-
Goood shit. Love this car
Thanks papa! Saw the new Rig Rocket. Bro'd out, Love it haha.
-
Goood shit. Love this car
Thanks papa! Saw the new Rig Rocket. Bro'd out, Love it haha.
Sick! How much power is it making now?
-
Goood shit. Love this car
Thanks papa! Saw the new Rig Rocket. Bro'd out, Love it haha.
Sick! How much power is it making now?
Ive played with horsepower calculators verifying how accurate they are... the most out I have seen is 50hp.
@3900lbs race weight and going 144mph its telling me 957 which is on 17psi, 16.5 degree timing, 50/50 race c16/pump as I never had a lap top or desire to look at the air fuel gauge hahah. I data logged one pass at the end of the night and we saw 11.3-11.5
-
Damn thats nasty!
Makes me want to ditch the lil D. :-X
-
this thing is awesome. just went threw the whole post again. realized i have never told you how cool i think it is.
good work. :noel:
Thanks!!
I actually just did the same and agree 100%, I'm in the process of de-hondaing and going to build a ls nova. might need some tech support! ever come to bc? lol.
Actually I do haha. I have lots of friends in the Kelowna area.
Ha! Me to, I'm only three hours from there :evil:
-
Actually heres an entertaining video... We were doing speed runs with some RC's. Fastest pass was 104mph lol. I didn't see the slash next to me. Just wanted to do a huge melter, 3rd gear... would have grabbed 6th if I had one.
https://www.youtube.com/watch?v=RRjBZTTOwPk&feature=youtube_gdata_player (https://www.youtube.com/watch?v=RRjBZTTOwPk&feature=youtube_gdata_player)
Nice!
-
Yeah I was out there with "boostedwagon" from here with his civic a few Friday's ago when Neil went 8.0x at Castrol. So close yet so far.
Are you welding out by Redwater? Mostly just drilling out that way as far as I know of.
Theres a couple kick ass turbo civics around this area. Neil did a dyno day and there was 3-4 well over 500fwhp. Last Friday a pretty nasty integra was there trapping 129mph if I remember right.
Im inspecting at the Williams/Pembina Plant. We are wrapping up an expansion and getting ready for the next one. In a 1km radius its nuts here. North West Upgrader put a call out for 2500 tradesman for their expansion which is within a km of our plant.
That is what boostedwagon trapped as well, but was out of gear, hopefully will go mid 130's with a new final drive.
Sweet, sounds like a good gig. My contracting stuff fell way off, so I picked up a real job, and just do a bit of lease building when called these days.
What are you doing for work now?? What car does boostedwagon have?
Sales, so I am living in a metal tube in the sky most days. He has a 92 civic hatch, white with a white cage, I think Highroller probably has a pic of it.
-
Yeah I was out there with "boostedwagon" from here with his civic a few Friday's ago when Neil went 8.0x at Castrol. So close yet so far.
Are you welding out by Redwater? Mostly just drilling out that way as far as I know of.
Theres a couple kick ass turbo civics around this area. Neil did a dyno day and there was 3-4 well over 500fwhp. Last Friday a pretty nasty integra was there trapping 129mph if I remember right.
Im inspecting at the Williams/Pembina Plant. We are wrapping up an expansion and getting ready for the next one. In a 1km radius its nuts here. North West Upgrader put a call out for 2500 tradesman for their expansion which is within a km of our plant.
That is what boostedwagon trapped as well, but was out of gear, hopefully will go mid 130's with a new final drive.
Sweet, sounds like a good gig. My contracting stuff fell way off, so I picked up a real job, and just do a bit of lease building when called these days.
What are you doing for work now?? What car does boostedwagon have?
Sales, so I am living in a metal tube in the sky most days. He has a 92 civic hatch, white with a white cage, I think Highroller probably has a pic of it.
ohh ok yup I saw that one. Back fired nicely every shift, making the females jump O0
-
Goood shit. Love this car
^this^
Any new vids?
Actually heres an entertaining video... We were doing speed runs with some RC's. Fastest pass was 104mph lol. I didn't see the slash next to me. Just wanted to do a huge melter, 3rd gear... would have grabbed 6th if I had one.
https://www.youtube.com/watch?v=RRjBZTTOwPk&feature=youtube_gdata_player (https://www.youtube.com/watch?v=RRjBZTTOwPk&feature=youtube_gdata_player)
Those are some dirty dirty lines :noel:
-
shit looks sick.. very good numbers! transbrake? or footbraking on launch?
-
shit looks sick.. very good numbers! transbrake? or footbraking on launch?
transbrake and 2 step :)
-
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_00551_zps376cc34c.jpg&hash=0b35f331e708d20a55f7ab9ac86fb1a9babba86b)
-
FAP FAP FAP FAP...
-
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_00551_zps376cc34c.jpg&hash=0b35f331e708d20a55f7ab9ac86fb1a9babba86b)
Front page this :noel:
Love the size of that turbo, I see a whole lot of fun right there. 8) 8) 8) 8) 8) 8) 8) 8) :evil: :evil: :evil: :evil: :evil: :evil: :evil:
-
haha thanks guys!, It still has full exhaust and sounds damn good IMO. I'll snap a video when I head home on the weekend. single 4" into dual 3.5"
Should work well :)
-
Damn this thing is so amazing!
If you ever ride through NJ lmk ill buy you a tank of gas for a ride :noel:
-
Damn this thing is so amazing!
If you ever ride through NJ lmk ill buy you a tank of gas for a ride :noel:
That could be expensive , but probably worth it. :noel:
-
Damn this thing is so amazing!
If you ever ride through NJ lmk ill buy you a tank of gas for a ride :noel:
That could be expensive , but probably worth it. :noel:
I dd a yukon with the same motor, your not telling me anything I dont already know hahaha
-
Made some noise with her today :)
http://youtu.be/35AGMA88LDs (http://youtu.be/35AGMA88LDs)
-
Damn that sounds sooooooo sexy! :noel:
-
Damn that sounds sooooooo sexy! :noel:
It made me giggle. :)
-
You don't know of any non rusty 62-67 novas do you good sir? I need a ls/turbo powered unit now.
-
off hand no :/ I had a damn rusty Acadian but sold it. It was so far gone..
-
alright back to shipping from cali lol
-
Can you post up some pics of the turbo/hot pipes/manis please. :noel:
-
Truck manifold cut and modified and I built the passenger side log/crossover piping.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_3169_zps2ef548c4.jpg&hash=d9d5b14a96d901a3bb447f37b6dbb940b3cd9740)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_3150_zps893e5795.jpg&hash=e12a2f012a9300746c53ae96c146c74547770011)
-
thats tight! any mounted up pics?
i need some nova ideas
-
thats tight! any mounted up pics?
i need some nova ideas
Why?, you can not find a decent Nova for a decent price. :noel:
-
You would be 50% wrong.
-
Hows that?
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2Fsingleturbs_zps8e46486f.jpg&hash=259c496fdd55f8d3a99c33df1d5e999e016abeb2)
-
thats tight! any mounted up pics?
i need some nova ideas
Why?, you can not find a decent Nova for a decent price. :noel:
hahahaha zinga!
Heres 2 cool pics. A friend and I did the intake pipes on both of these trucks. 540ci big block chebs, Steve Morris belt driven prochargers, billet atomizer injectors, Holley Dominator ECU, on methonal. Should be 2000hp or so. Bracket deals.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2Fprocharger1_zpsa4003464.jpg&hash=0c5c005e807507c9eced7237ab44a23d182cf494)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2Fprocharger_zps6d29b27c.jpg&hash=efaf42346694278080bbe1e84247e57e59df9d9f)
-
jesus O0
what did you run for manis on your twin setup?
-
homemade muh fuckiin logs nigguh. O0
Im sure you want some pics of those too, you demanding cracker
-
I just want new vids!
-
Lol!!! I'll come drink your beer one of these days as a thanks!!! ;)
-
Just went back through this whole thread. Simply bad ass.
-
Anyone know how to get a hold of this nog? I've been looking into reviving my 67 bird and he's done some of the upgrades I'm looking at.
-
He's on ls1tech
-
Yes, and the oil patch I believe lol.
Car is awesome, can't wait to get a setup on the nova :(
-
Anyone know how to get a hold of this nog? I've been looking into reviving my 67 bird and he's done some of the upgrades I'm looking at.
Sorry homie!!! Im alive! feel free to shoot me an email @ caninspectionATgmailDOTcom
Im alive... What an expensive fucking summer. Let me upload some pictures. lol
-
Yes, and the oil patch I believe lol.
Car is awesome, can't wait to get a setup on the nova :(
Oilpatch is right haha. what a damn ride its been!
-
OK long and short....
A-1 Transmission out of Vancouver Washington sucks donkey dick. They soaked me for 3k for a TH400. yea it had billet shiny parts inside but they were all machined way the fuck wrong, installed a valve body that worked but had a severe high gear leak, it was killing clutches, bearings, etc. Tolerances were too tight in some places and too sloppy in others... Hutch Transmissions in Ontario fixed me up. I was out that way for work and was able to swing by and spend some time with him too!!
So with that said... there was a massive restriction in the transmission from eating material. Some is to do with inside the trans, others is when the trans was slowly killing itself it was also plugging up the transmission cooler. Which in turn pushed the converter into the crank resulting in wiping the thrust bearings out on my 150km new engine! (LS3 crank, k1 rods, weisco pistons)
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_18521_zps898102c6.jpg&hash=3df5183f874a611a531bbca95877df83302db679)
It gets better.... the crank made love to the mains.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_19771_zps5d3bc6be.jpg&hash=41045367c86d43dfd6674c2c189a5769da7be5eb)
Oh wait it gets better... That LS3 crank...
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FFullSizeRender_zpsdqppracf.jpg&hash=61a6e12c7fe2cca11e9d316fa5de79a5b2087093)
Soooo now the new build started.
K1 forged crank, k1 rods, weisco pistons. Now Im gonna lean on it, magna fuel 4303 fuel pump, etc. 1k or Ill hang myself. #sleddeckproblems #berta!
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_2847_zpslkbcgmgq.jpg&hash=5c98dc741f56a4f7de85766c1063a5fd2c535930)
-
New TH400 from Hutch Transmissions.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_2208_zps66a07950.jpg&hash=5457a8e88c322c4cef00d577da88e97a10f9259b)
So then I also bought a 58 Apache off of my sister.. Wanted to LS swap it so I decided to use the old smoking 6.0l from chevelle. Was going to knob hone and re ring it, until I found this...
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_2437_zpskhnsq56d.jpg&hash=a2d6432d566f7ccaf905a825f779cfe01d4bd4cf)
So naturally I found another piston... gapped the rings, honed the cylinder(#7) and now its ready to go in. I also sent my billet 76 to get converted to a billet 84... while they pulled the billet 76 wheel off I had them put that wheel on a cast race cover 76mm which will now go on the apache. lol
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_2504_zpswhwkjjs2.jpg&hash=3faf95ed7ab9eaee96843adc1ec920951b36bf62)
I also built a 9" for it, dutchman 35spline axles, mini spool and I think 3:50 gears. Summit disc brake kit.
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_2259_zpsn4zcdsh3.jpg&hash=cc93fecc47f9f7aa0ad26867417f8263dcd3e1b4)
A cool picture of the chevelle 6.0l(red valve covers), apache engine(middle) and a spare 5.3
(https://realhomemadeturbo.com/forum/proxy.php?request=http%3A%2F%2Fi59.photobucket.com%2Falbums%2Fg314%2Fprotour%2FIMG_2857_zpseqw4zisc.jpg&hash=c78fc70687591800e2e92336f8bad11018b1acf6)
-
Shitty luck man. I would be so pissed but I'm sure they put the blame on something you did ::) Fucking niggers. Onto bigger and better things. Hope the new setup works out for you. Still a cool fucking build.
-
Shitty luck man. I would be so pissed but I'm sure they put the blame on something you did ::) Fucking niggers. Onto bigger and better things. Hope the new setup works out for you. Still a cool fucking build.
Oh yea, they wouldn't admit to fuck all but as soon as Hutch went through it with me it was evident. Hutch spent 5 hours pumping fluid into the valve body trying to convince himself he wasn't the fucking moron. He called me later on and said my valve body was a butchered pile of shit and it is now located in the trash can hahaha. His support/knowledge is killer. The REALLY shitty part is when I first switched to a th400 it was hutch or a-1(friends suggestion), well I made the mistake and am paying for it! Live and learn.
-
Other than the massive fuckery, I heart everything about your updates. Cant beat 2 cool as fuck heavy chevys doin work!
-
Other than the massive fuckery, I heart everything about your updates. Cant beat 2 cool as fuck heavy chevys doin work!
Holy shit long time no see!!
-
Anyone know how to get a hold of this nog? I've been looking into reviving my 67 bird and he's done some of the upgrades I'm looking at.
Sorry homie!!! Im alive! feel free to shoot me an email @ caninspectionATgmailDOTcom
Im alive... What an expensive fucking summer. Let me upload some pictures. lol
Great to hear you're still around & still have the Chevelle. That really sucks about the tranny issue, I just hope the guy I used years ago is still working on them. He worked 16+ hrs a day on trannies for 9 months, then he'd take 3 months off.
Your car is practically the model I'd like my bird to live up to, going a little bit at a time. I think I can write-off a lot of the upgrades since it will be a combination show car & test bed for injectors.
-
My brother in law had a cumminGs with a smarty and toes 10k daily on 35's and flipped up tow mirrors. His trans went out at 150,000km, guy in Calgary built him a trans that would hold "1500 hp" lasted two Weeks, he went threw it again and it lasted three weeks, (keep in mind he works 10 hour days at 100 bucks an hour, 7 days a week and now can't work) then he was told he towed too heavy and to fuck off. Guys 300 pounds and benches 400 lbs like its the bar. I don't understand shit like that. I'd rather go broke then push shit out my shops door.
-
BTW those engine stands are the shit!
-
Damn so much win (besides the fagget trans guys) cant wait to see both cars ripping!!!
-
BTW those engine stands are the shit!
That was a "Im too lazy to hit buy it now and I want to blow my afternoon making engine stands" moment haha
-
Damn so much win (besides the fagget trans guys) cant wait to see both cars ripping!!!
You and me both brother!
-
Trucks awesome. I would build a ls c10 or f100 but the family doesn't sit in a std cab :-\
-
Makes me want to take a road trip for some rippers haha
-
Makes me want to take a road trip for some rippers haha
Youre more than welcome once this heap is back breathing again haha.
-
Im mentally handicap with linking shit and whatever but for the faggets that are on instagram... cst_koon. I posted a 12 second clip on 10 pounds. It sounds fun :)
-
Time for some 1000hp pulls. :noel:
-
so much sexy.....
-
so much sexy.....
Heres a 10lb 2nd gear melter. hahaha
https://youtu.be/gw2JnZM2mto (https://youtu.be/gw2JnZM2mto)
-
And the instagram one on youtube
https://youtu.be/iv_-f-x0_wY
-
Time for some 1000hp pulls. :noel:
agreed! gotta put the new fuel pump in then turn the bitch up!
-
Fuck I was even in Red Deer last week. I should have hit you up for a ride.
-
so much sexy.....
Heres a 10lb 2nd gear melter. hahaha
https://youtu.be/gw2JnZM2mto (https://youtu.be/gw2JnZM2mto)
so badass
-
Fuck I was even in Red Deer last week. I should have hit you up for a ride.
you dumbfuck! O0
-
Fuck I was even in Red Deer last week. I should have hit you up for a ride.
you dumbfuck! O0
I know, I know... :'(
-
Bretts not usally antisocial, that's my job lol O0
-
Bretts not usally antisocial, that's my job lol O0
hahah, Im generally antisocial to the random cling ons that have no fucking idea what they are talking about when they see my car in person, ask me stupid questions, etc.
Who am I kidding... the older I get the more I hate people hahahah :noel:
-
You and I would get along great lol.
-
This cock roach went 8.79@154 on 23psi and 16 degrees of timing, 4th pass of its life with this setup.
I'll get more aggressive with the boost ramp and front half of the track this year. Also need to adjust some things like the diff and would like to put new shocks in it.
1.31 60'. Would like to see 1.2x
-
heres a low 9 second run
https://youtu.be/pHiLZlowiuA
IF you slow the video down at the launch, you can see that the rear diff is obviously not in the car straight. Need to sort that out. Its all adjustable shit. 35 spline axles with spool so its not a limited slip issue. Tires are spinning on the rim but only about 3/8" per run, same movement. I will glue the tires. Beadlocks aren't in the budget this year. #2016problems
-
Makes my pants tight!!
-
That thing is just fucking beautiful
-
Makes my pants tight!!
haha thanks!
Man where have most of the members flocked to? Traffic is sloooow round here!
-
Facebook Rhmt groups get more then here but still not allot lol