Topic: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46 (Read 7608 times)

Lowerit · « **on:** April 30, 2009, 10:05:31 PM »

Rawr's thread inspired me to tackle my own engine and tranny mounts , this is the rear tranny mount from an EG..

and yes, those are Hockey Pucks. $1.23 Ea.

Don't need a press either.

Saws all
2 Hockey Pucks
Torch
Drill
Rivets
WD-40

Cut out the center

Cheap ass hockey puck (vulcanized hardass rubber)

Cut a bit off the bottom of the hockey puck

Take the old chunk with the steel insert.. heat the fuck out of the insert and push it put

Drill a big ass hole for the steel insert

Done

1 Hockey puck per side , I just pressed it in with the vice and some WD40, they were in there tight as hell , but for added security I drilled a few small holes in the top on each side and put rivets in them...

and thats my cheap ass GRM motor mount...

92CXyD · « **Reply #1 on:** April 30, 2009, 10:08:13 PM »

I like that I may have to try that eventhough my window weld urethane filled are holding up pretty good so far. ;D

Teg2boo · « **Reply #2 on:** April 30, 2009, 10:12:48 PM »

I'll give it a try. At least you don't need to wait for the urethane to dry out.

lilpooh21186 · « **Reply #3 on:** April 30, 2009, 11:07:52 PM »

baller statis

patsmx5 · « **Reply #4 on:** April 30, 2009, 11:14:28 PM »

Quote from: lilpooh21186 on April 30, 2009, 11:07:52 PM

baller statis

imburne · « **Reply #5 on:** April 30, 2009, 11:25:22 PM »

Keep it white brother

Let us know how it feels.

danz · « **Reply #6 on:** May 01, 2009, 01:53:03 AM »

Quote from: 92CXyD on April 30, 2009, 10:08:13 PM

I like that I may have to try that eventhough my window weld urethane filled are holding up pretty good so far. ;D

mine have been on my DD for over a year and still look new. high build urethane used for installing windshields.

Passenger · « **Reply #7 on:** May 01, 2009, 07:04:25 PM »

I used to do this with VW's all the time, works great!

Toysrme · « **Reply #8 on:** May 01, 2009, 08:34:11 PM »

dogbone torque mount in my lexus is a hockey puck after the urathane window weld gave way. a year or so back.
mines doing good so far too.

Sinister · « **Reply #9 on:** May 02, 2009, 12:53:04 PM »

Quote from: Passenger on May 01, 2009, 07:04:25 PM

I used to do this with VW's all the time, works great!

A friend of mine just did this weeks ago, loves it. Best part is he got the hockey pucks for free from a friend who had ~20 left in his car when he bought it, so his entire cost was $0

caged · « **Reply #10 on:** May 04, 2009, 02:20:24 AM »

I just did my engine mount for my evo 2. Perfect size with no cutting required

. My pucks were 4$ each. Thanks for a great write up!

t_cel_t · « **Reply #11 on:** May 04, 2009, 03:57:18 AM »

my rear mount, been on 3 cars and ~50,000+ mi so far

Urban Indian · « **Reply #12 on:** May 05, 2009, 12:30:14 PM »

Piiiiimp

I need a torch

caged · « **Reply #13 on:** May 05, 2009, 05:54:48 PM »

Quote from: Urban Indian on May 05, 2009, 12:30:14 PM

Piiiiimp

I need a torch

I found it was quicker to use a flat blade screw driver and a hammer to chissil it out, then use the torch to burn whats left. I still managed to set the workshop smoke detector off lol.

Urban Indian · « **Reply #14 on:** May 06, 2009, 04:48:07 AM »

I still need a torch though. I used a drill, chisel, screw driver, hole saw......... fuck that liquid shit inside the driver side mounts....... gross shit in there

Lowerit · « **Reply #15 on:** May 06, 2009, 10:35:20 AM »

U don't need a real torch, just propane $5 crap.

Eggylshatch · « **Reply #16 on:** May 09, 2009, 11:30:58 PM »

I would want to use a little polyurethane in there with the hockey pucks to glue them in/together. It would serve as your lubrication to slide the pucks in there too, and dry up solid as FUCK.

tersplat · « **Reply #17 on:** May 18, 2009, 02:50:27 PM »

been using them on my tercel for all 3 mounts for over a year not just like t_cel_t he's the one who gave me the idea with a wrieup he posted on tercelonline. they work great.

88dx · « **Reply #18 on:** May 18, 2009, 03:34:28 PM »

Quote from: Urban Indian on May 06, 2009, 04:48:07 AM

I still need a torch though. I used a drill, chisel, screw driver, hole saw......... fuck that liquid shit inside the driver side mounts....... gross shit in there

I had one of those explode leaving the line at mission raceway on slick's and when I poped the hood i was like WTF

Shit looks nasty and went everywhere

Lowerit · « **Reply #19 on:** May 20, 2009, 09:05:48 AM »

I am going to be doing 3 more mounts this weekend. Will post up more pics. i think i am going to fill the centers with Poly as suggested.

92CXyD · « **Reply #20 on:** May 20, 2009, 09:16:10 AM »

Quote from: Eggylshatch on May 09, 2009, 11:30:58 PM

I would want to use a little polyurethane in there with the hockey pucks to glue them in/together. It would serve as your lubrication to slide the pucks in there too, and dry up solid as FUCK.

Great idea I will be trying this after Wa. meet. ;D

News:

Author Topic: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46 (Read 7608 times)