:::RHMT::: Real Home Made Turbo

Please login or register.

Login with username, password and session length
Advanced search  

News:

Daspoop/Trevor YOU WILL BE MISSED, RIP (link)  :'(

Pages: [1]   Go Down

Author Topic: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46  (Read 9336 times)

Lowerit

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 101185

Rawr's thread inspired me to tackle my own engine and tranny mounts , this is the rear tranny mount from an EG..

and yes, those are Hockey Pucks.  $1.23 Ea.

Don't need a press either.

Saws all
2 Hockey Pucks
Torch
Drill
Rivets
WD-40



Cut out the center


Cheap ass hockey puck (vulcanized hardass rubber)



Cut a bit off the bottom of the hockey puck



Take the old chunk with the steel insert.. heat the fuck out of the insert and push it put


Drill a big ass hole for the steel insert



Done




1 Hockey puck per side , I just pressed it in with the vice and some WD40, they were in there tight as hell , but for added security I drilled a few small holes in the top on each side and put rivets in them...


and thats my cheap ass GRM motor mount...

« Last Edit: April 30, 2009, 10:11:27 PM by Lowerit »
Logged
fuck you

92CXyD

  • Twincharged Smeghead
  • Global Moderator
  • Certified OG
  • *****
  • Online Online
  • Posts: 6759
  • I look around and all I see is Smegheads
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.
« Reply #1 on: April 30, 2009, 10:08:13 PM »

I like that I may have to try that eventhough my window weld urethane filled are holding up pretty good so far. ;D

Teg2boo

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 4261
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.
« Reply #2 on: April 30, 2009, 10:12:48 PM »

I'll give it a try. At least you don't need to wait for the urethane to dry out.
Logged


damn you guys too? its a fucking forum not a court room!
 Its not a forum its a gang.  

lilpooh21186

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1801
  • B16 Short strokes but holds a high note
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #3 on: April 30, 2009, 11:07:52 PM »

baller statis
Logged
Ecu chipping
basmaps
tuning Dyno/street pm for details
Neptune Dealer PM for RTP details

patsmx5

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1584
Logged
Quote: Originally Posted by Adam Hopkins
There is no such thing as too much boost. You could have too little rod, piston, or sleeve. But never too much boost.

imburne

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3983
    • TurboByHOLSET
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #5 on: April 30, 2009, 11:25:22 PM »

Keep it white brother  ;) Let us know how it feels.

danz

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 6783
  • 0-60 in 2.7 seconds
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.
« Reply #6 on: May 01, 2009, 01:53:03 AM »

I like that I may have to try that eventhough my window weld urethane filled are holding up pretty good so far. ;D

mine have been on my DD for over a year and still look new.  high build urethane used for installing windshields. 
Logged
10.510 @ 133.09 mph D16Z6 EJ6
10.912 @ 127.33 mph D16A6 ED6

Passenger

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 1954
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #7 on: May 01, 2009, 07:04:25 PM »

I used to do this with VW's all the time, works great!
Logged

Toysrme

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 250
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #8 on: May 01, 2009, 08:34:11 PM »

dogbone torque mount in my lexus is a hockey puck after the urathane window weld gave way. a year or so back.
mines doing good so far too.

Sinister

  • insane in the membrane
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 21489
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #9 on: May 02, 2009, 12:53:04 PM »

I used to do this with VW's all the time, works great!

A friend of mine just did this weeks ago, loves it. Best part is he got the hockey pucks for free from a friend who had ~20 left in his car when he bought it, so his entire cost was $0
Logged
Join Date: 12-31-2003
Posts: 20174
3/5/09 - RIP HMT

caged

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 364
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #10 on: May 04, 2009, 02:20:24 AM »

I just did my engine mount for my evo 2. Perfect size with no cutting required  :noel:. My pucks were 4$ each. Thanks for a great write up!
Logged
11.6@126mph 1993 mitsubishi GSR.

t_cel_t

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3147
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #11 on: May 04, 2009, 03:57:18 AM »

my rear mount, been on 3 cars and ~50,000+ mi so far



Logged
malone labe

I think all cop cars need to have turbo. nbspnbsp Then they would understand the necessity of putting your foot down and how uncontrollable the urge is to fucking rail on that shit.

Urban Indian

  • Snow Mexican
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3383
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #12 on: May 05, 2009, 12:30:14 PM »

Piiiiimp


I need a torch
Logged
The clock doesn'#039#039t own me

 Topless chick + dominos pizza + 750hp civic = epic win

caged

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 364
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #13 on: May 05, 2009, 05:54:48 PM »

Piiiiimp


I need a torch

I found it was quicker to use a flat blade screw driver and a hammer to chissil it out, then use the torch to burn whats left. I still managed to set the workshop smoke detector off lol.
« Last Edit: May 07, 2009, 01:38:26 AM by caged »
Logged
11.6@126mph 1993 mitsubishi GSR.

Urban Indian

  • Snow Mexican
  • Certified OG
  • *****
  • Offline Offline
  • Posts: 3383
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #14 on: May 06, 2009, 04:48:07 AM »

I still need a torch though. I used a drill, chisel, screw driver, hole saw......... fuck that liquid shit inside the driver side mounts....... gross shit in there
Logged
The clock doesn'#039#039t own me

 Topless chick + dominos pizza + 750hp civic = epic win

Lowerit

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 101185
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #15 on: May 06, 2009, 10:35:20 AM »

U don't need a real torch, just propane  $5 crap.
Logged
fuck you

Eggylshatch

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 2188
  • Pen15 Club President
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #16 on: May 09, 2009, 11:30:58 PM »

I would want to use a little polyurethane in there with the hockey pucks to glue them in/together.  It would serve as your lubrication to slide the pucks in there too, and dry up solid as FUCK.
Logged

tersplat

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 13
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #17 on: May 18, 2009, 02:50:27 PM »

been using them on my tercel for all 3 mounts for over a year not just like t_cel_t he's the one who gave me the idea with a wrieup he posted on tercelonline. they work great.
Logged

88dx

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 7885
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #18 on: May 18, 2009, 03:34:28 PM »

I still need a torch though. I used a drill, chisel, screw driver, hole saw......... fuck that liquid shit inside the driver side mounts....... gross shit in there
I had one of those explode leaving the line at mission raceway on slick's and when I poped the hood i was like WTF  :-X Shit looks nasty and went everywhere  :?:
Logged

Lowerit

  • Certified OG
  • *****
  • Offline Offline
  • Posts: 101185
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #19 on: May 20, 2009, 09:05:48 AM »

I am going to be doing 3 more mounts this weekend. Will post up more pics. i think i am going to fill the centers with Poly as suggested.
Logged
fuck you

92CXyD

  • Twincharged Smeghead
  • Global Moderator
  • Certified OG
  • *****
  • Online Online
  • Posts: 6759
  • I look around and all I see is Smegheads
Re: RHMT Motor mounts.. Not Poly or Derlin... 75% more RHTM Cost $2.46
« Reply #20 on: May 20, 2009, 09:16:10 AM »

I would want to use a little polyurethane in there with the hockey pucks to glue them in/together.  It would serve as your lubrication to slide the pucks in there too, and dry up solid as FUCK.

Great idea I will be trying this after Wa. meet. ;D
Pages: [1]   Go Up